Mitsubishi Electric MDT5525 User Manual Page 34

  • Download
  • Add to my manuals
  • Print
  • Page
    / 58
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 33
(34/58)
10.2 Schedule Write
This command is used in order to write the setting of the Schedule.
1) The controller requests the monitor to write Schedule
.
Header Message Check code Delimiter
SOH-'0'-'A'-'0'-'A'-'1'-'6' STX-'C'-'2'-'1'-'4'-PG-ON HOURS-ON MIN-
O
FF
HOURS-OFF Min-INPUT-WD-FL-ETX
BCC CR
Header
SOH (01h): Start Of Header
'0' (30h): Reserved
'A' (41h): Monitor ID
If the command should be sent to certain monitor only, the either of character ‘A’(41h) to Z’(5Ah)
which is corresponding to monitor ID from No1 to No.26 should be set to this portion. If it
is a broad cast command (only “set command” is available), then the ’*’(2Ah)should be applied.
'0' (30h): Message sender is the controller
'A' (41h): Message type is "Command"
'1'-'6'(31h, 36h): Message length.
Message
STX (02h): Start of Message
'C'-'2'-'1'-'4' (43h, 32h, 31h, 34h): Schedule writes command
PG-ON HOURS-ON MIN-OFF HOURS-OFF Min-INPUT-WD-FL: Schedule data
PG: Program No.
'0'-'0'(30h, 30h): Program No.1
|
'0'-'6'(30h, 36h): Program No.7
ON_HOUR: Turn on time (hour)
'0'-'0'(30h, 30h): 00
|
'1'-'7'(31h, 37h): 23 (=17h)
'1'-'8'(31h, 38h): ON timer isn't set.
ON_MIN: Turn on time (minute)
'0'-'0'(30h, 30h): 0
|
'3'-'B'(33h, 42h): 59
'3'-'C'(33h, 43h): On timer isn’t set.
OFF_HOUR: Turn off time (hour)
'0'-'0'(30h, 30h): 00
|
'1'-'7'(31h, 37h): 23 (=17h)
'1'-'8'(31h, 38h): Off timer isn't set.
OFF_MIN: Turn off time (minute)
'0'-'0'(30h, 30h):0min
|
'3'-'B'(33h, 42h):59 (=3Bh)
'3'-'C'(33h, 43h): Off timer isn’t set.
INPUT: Timer input
'0'-'0'(30h, 30h): HDMI1
'0'-'A'(30h, 41h): HDMI2
'0'-'1'(30h, 31h): DVI-D
'0'-'2'(30h, 32h): D-SUB
'0'-'4'(30h, 34h): YpbPr(DVD/HD)
'0'-'5'(30h, 35h): VIDEO
'0'-'6'(30h, 36h): S-VIDEO
'0'-'7'(30h, 37h): It is o
perates by last memory input
'0'-'8'(30h, 38h): OPTION
'0'-'9'(30h, 39h): DisplayPort
WD: Week setting
bit 0: Monday
Page view 33
1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 57 58

Comments to this Manuals

No comments