Mitsubishi Electric FR-A7AY Instruction Manual

INSTRUCTION MANUAL23456INVERTERPlug-in option1FR-A7AYFR-A7AY E kitAnalog output functionDigital output functionINSTALLATION AND WIRING(FR-E700 SERIES

5PRE-OPERATION INSTRUCTIONS11.4 Specifications(1) Output signalsVoltage output (across terminals AM0-AMC) 0 to 10VDCMAXCurrent output (across terminal

62 INSTALLATION AND WIRING (FR-A700/F700 SERIES)2.1 Pre-Installation InstructionsMake sure that the input power of the inverter is off.CAUTIONWith inp

7INSTALLATION AND WIRING (FR-A700/F700 SERIES)22.2 Installation Procedure1)Remove the inverter front cover.2)Mount the hex-head screw for option mount

8INSTALLATION AND WIRING (FR-A700/F700 SERIES)CAUTION• Only one type of option per inverter may be used. When two or more options are mounted, priorit

9INSTALLATION AND WIRING (FR-A700/F700 SERIES)22.3 Wiring(1) Untwist the twisted pair shielded cables after stripping its sheath.Also, perform protect

10INSTALLATION AND WIRING (FR-A700/F700 SERIES)(2) Loosen the terminal screw and insert the cable into the terminal. Screw Size Tightening Torque Cabl

11INSTALLATION AND WIRING (FR-A700/F700 SERIES)2(3) For wiring of the FR-A700 series 22K* or less and the FR-F700 series 30K* or less, route wires bet

12INSTALLATION AND WIRING (FR-A700/F700 SERIES)REMARKS• When the hook of the inverter front cover is cut off for wiring, the protective structure (JEM

1333INSTALLATION AND WIRING (FR-E700 SERIES (E kit))3.1 Pre-Installation InstructionsMake sure that the input power of the inverter is off.3.2 Install

14INSTALLATION AND WIRING (FR-E700 SERIES (E kit))z For FR-E720-3.7K (FR-E720-175) or less, FR-E740-7.5K (FR-E740-170) or less(1) Remove the front cov

A-1Thank you for choosing this Mitsubishi Inverter plug-in option.This instruction manual gives handling information andprecautions for use of this eq

15INSTALLATION AND WIRING (FR-E700 SERIES (E kit))3(3) Install the option protective cover.(4) Securely fit the connector of the plug-in option to the

16INSTALLATION AND WIRING (FR-E700 SERIES (E kit))z For FR-E720-5.5K (FR-E720-240) or more, FR-E740-11K (FR-E740-230) or more(1) Remove the front cove

17INSTALLATION AND WIRING (FR-E700 SERIES (E kit))3(4) Securely fit the connector of the plug-in option to the inverter connector along the guides.(5)

18INSTALLATION AND WIRING (FR-E700 SERIES (E kit))3.3 Wiring(1) Untwist the twisted pair shielded cables after stripping its sheath.Also, perform prot

19INSTALLATION AND WIRING (FR-E700 SERIES (E kit))3(2) Loosen the terminal screw and insert the cable into the terminal. Screw Size Tightening Torque

20INSTALLATION AND WIRING (FR-E700 SERIES (E kit))(3) When wiring the FR-E700 series, if a hook of the front cover for the plug-in option impedes wiri

2144 PARAMETER LISTWhen the FR-A7AY is mounted on the inverter, the following parameters are extended.Parameter NumberName Setting RangeMinimumSetting

22PARAMETER LIST*1 The setting range differs according to the inverter. For details refer to page 30, 32.*2 The setting range differs according to th

2355 EXTENSION ANALOG OUTPUT5.1 Wiring ExampleBy setting the Pr. 306 to Pr. 312 values, analog signals such as the output frequency and output current

24EXTENSION ANALOG OUTPUT5.2 Internal Block DiagramThe following is the internal block diagram about the FR-A7AY analog output function.ControllerConn

A-22. Injury Prevention3. Additional InstructionsAlso note the following points to prevent an accidental failure,injury, electric shock, etc.1) Transp

25EXTENSION ANALOG OUTPUT55.3 TerminalsTerminal Symbol Terminal Name DescriptionAM0Voltage output terminalConnect a DC voltmeter (10VDC).AM1Current ou

26EXTENSION ANALOG OUTPUT5.4 Extension Analog Output Function Parameter List* The setting range differs according to the inverter. For details refer t

27EXTENSION ANALOG OUTPUT55.5 Adjustment Procedure5.5.1 Setting of analog output signal voltage/current switchover (Pr. 309)Use Pr. 309 Analog output

28EXTENSION ANALOG OUTPUT5.5.2 Calibration of meter(1) Outputting the same select signals from terminals AM0 and AM1 (Pr. 309 = "0 or 10")At

29EXTENSION ANALOG OUTPUT5(2) Outputting different select signals from terminals AM0 and AM1 (Pr. 309 = "1 or 11")STARTAt this time, check t

30EXTENSION ANALOG OUTPUT5.5.3 Output signal setting (FR-A700/F700 series)Set the output signals to be monitored. Set Pr. 306 to output the same signa

31EXTENSION ANALOG OUTPUT5*1 This parameter value is not available with the FR-F700 series 55K or less.*2 The setting depends on capacities. (55K or l

32EXTENSION ANALOG OUTPUT5.5.4 Output signal setting (FR-E700 series)Set the output signals to be monitored. Set Pr. 306 to output the same signal fro

33EXTENSION ANALOG OUTPUT55.5.5 Analog signal adjustment [Pr. 307, Pr. 308, Pr. 311, Pr. 312]Use Pr. 307 or Pr. 311 to set the value for zero analog o

34EXTENSION ANALOG OUTPUT5.6 Instructions(1) A voltmeter having smaller internal impedance (or an ammeter having larger internal impedance) than the v

I— CONTENTS —1 PRE-OPERATION INSTRUCTIONS 11.1 Inverter Type ...

3566 DIGITAL OUTPUT6.1 Internal Block DiagramThe following is the internal block diagram about the FR-A7AY digital output functionControllerConnectorY

36DIGITAL OUTPUT6.2 TerminalsBy setting the Pr. 313 to Pr. 319 values, output signals (RUN, SU etc.) available with an inverter as standardcan be outp

37DIGITAL OUTPUT66.3 Digital Output Function Parameter List* The setting range differs according to the inverter. For details refer to page 38, 40.Pa

38DIGITAL OUTPUT6.4 Output Signal List (FR-A700/F700 series)For details of signal definitions, refer to Pr. 190 to Pr. 196 (Output terminal function s

39DIGITAL OUTPUT6*1 They can be set for the FR-A700 series only.*2 For the FR-F700 series, this function is available with the 75K(FR-F720-03610, FR-F

40DIGITAL OUTPUT6.5 Output Signal List (FR-E700 series)For details of signal definitions, refer to Pr. 190 to Pr. 192 (Output terminal function select

41REVISIONS*The manual number is given on the bottom left of the back cover.Print Date *Manual Number RevisionMay, 2004 IB(NA)-0600165ENG-A First edit

II5.4 Extension Analog Output Function Parameter List...265.5 Adjustment Procedure

111 PRE-OPERATION INSTRUCTIONS1.1 Inverter TypeThe inverter type, 55K and 75K stated in this Instruction Manual differs according to each -NA, -EC, -C

2PRE-OPERATION INSTRUCTIONS1.2 Unpacking and Product ConfirmationTake the plug-in option out of the package, check the product name, and confirm that

3PRE-OPERATION INSTRUCTIONS11.2.2 Packing confirmation (FR-E700 series (E kit))Check the enclosed items.*1 Used with the FR-E720-3.7K (FR-E720-175) or

4PRE-OPERATION INSTRUCTIONS1.3 PartsAMCNCSEY3Y4Y5Y6AM0AM1NCSEY0Y1Y2Front viewTerminal layoutRear viewMounting holeMounting holeMounting holeTerminal b