Mitsubishi Electric PURY-HP96T Installation Manual Page 237
- Page / 334
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
[ IX Troubleshooting ]
- 228 -
HWE09120 GB
In case of ME remote controller
1. Phenomena
Even if the operation button on the remote controller is pressed, the display remains unlit and the unit does not start running.
(Power indicator does not appear on the screen.)
(1) Cause
1) The power for the M-NET transmission line is not supplied from the outdoor unit.
2) Short circuit of the transmission line.
3) Incorrect wiring of the M-NET transmission line on the outdoor unit.
Disconnected wire for the MA remote controller or disconnected line to the terminal block.
The indoor transmission line is connected incorrectly to the transmission terminal block for centralized controller (TB7).
4) Disconnected transmission line on the remote controller.
5) Remote controller failure
6) Outdoor unit failure (Refer to IX [7] Troubleshooting Using the Outdoor Unit LED Error Display.)(page 278)
(2) Check method and remedy
1) Check voltage of the transmission terminal block for of the ME remote controller.
If voltage between is 17V and 30V -> ME remote controller failure
When voltage is 17V or less -> Refer to IX [4] -7- (2) " Troubleshooting transmission power circuit of outdoor unit".
2) When 2) and 3) above apply, check code 7102 will be displayed on the self-diagnosis LED.
- Safety Precautions 2
- Before installing the unit 5
- Before the test run 7
- CONTENTS 8
- Read Before Servicing 10
- [1] Read Before Servicing 12
- [3] Piping Materials 14
- Dimension A 15
- [4] Storage of Piping 16
- [5] Pipe Processing 16
- [6] Brazing 17
- [7] Air Tightness Test 18
- [9] Refrigerant Charging 20
- [ I Read Before Servicing ] 23
- Restrictions 24
- [1] System configuration 26
- Terminal 31
- [ II Restrictions ] 32
- Example of wiring connection 32
- (*4, *5) 34
- [4] Sample System Connection 35
- Interlock operation with 37
- Group Group 37
- M1 M2 M1 M2 M1 M2 M1 M2 41
- M1 M2 M1 M2 41
- M1 M2 M1 M2 M1 M2 M1 M2 43
- System controller 45
- Group Group Group 45
- GBHWE09120 49
- Unit: m [ft] 51
- 165 [541] or less 51
- (Equivalent length 190 51
- [623] or less) 51
- Outdoor Unit Components 56
- (1) PUHY-P72, P96TJMU-A 58
- PUHY-P72, P96YJMU-A 58
- (2) PUHY-P120, P144TJMU-A 59
- PUHY-P120, P144YJMU-A 59
- (3) PUHY-P120, P144TJMU-A 61
- <HIGH VOLTAGE WARNING> 62
- (R1,R5) Note.2 63
- Transformer 64
- 2. M-NET board 66
- 4. Fan board 70
- 5. Noise Filter 72
- (1) PUHY-P72TJMU-A 72
- Remote Controller 76
- [ IV Remote Controller ] 79
- Electrical Wiring Diagram 86
- <Symbol explanation> 88
- Refrigerant Circuit 94
- 1. Outdoor unit 96
- (1) PUHY-P72, P96 models 96
- (2) PUHY-P120, P144 models 96
- 273 t 98
- HWE09120 GB 100
- [ VI Refrigerant Circuit ] 101
- Clogged filter detection 108
- Initial vane position 108
- Switch setting timing 109
- (left) (right) 110
- Remote controller unit 110
- Rotary switch 110
- -1- Outline of Control Method 111
- -2- Startup sequence rotation 111
- -3- Initial Control 111
- -4- Control at Start-up 111
- -5- Bypass Control 112
- -7- Defrost Operation Control 114
- 30 seconds 116
- [ VII Control ] 118
- (3) P312, P336, P368 models 119
- -13- Emergency Operation Mode 120
- -14- Operation Mode 122
- -15- DEMAND Control 123
- [3] Operation Flow Chart 124
- 2. Operations in each mode 126
- (1) Cooling operation 126
- Test run mode 127
- Thermostat ON 127
- 1 or 2 128
- Suction temperature 128
- 18°C[64°F] 128
- Test Run Mode 130
- [2] Test Run Method 133
- Liquid 136
- Self-diagnosis swithes on TH4 137
- Self-diagnosis swithes on TH6 137
- Self-diagnosis swithes on TH3 137
- Self-diagnosis swithes on Tc 137
- OC, OS1, and OS2.) 138
- Troubleshooting 162
- Outdoor unit 164
- Indoor unit 164
- Remote controller 164
- 0403 (TJMU-A) 167
- 0403 (TJMU-A) (Indoor unit) 167
- 0403 (YJMU-A) 168
- 0403 (YJMU-A) (Indoor unit) 168
- +0,-0.15 171
- 4102 (TJMU-A) 179
- 4102 (YJMU-A) 180
- (TJMU-A) 183
- (YJMU-A) 186
- 4230 (TJMU-A) 190
- 4230 (YJMU-A) 191
- 4240 (TJMU-A) 192
- 4240 (YJMU-A) 193
- 4250 (TJMU-A) 196
- 4250 (YJMU-A) 197
- 4260 (TJMU-A) 198
- 4260 (YJMU-A) 198
- 5110 (YJMU-A) 202
- 5301 (TJMU-A) 203
- 5301 (YJMU-A) 204
- Measure voltages of the 234
- Is the error code 7102 234
- [ IX Troubleshooting ] 236
- Flow chart 236
- Connector contact failure 238
- High pressure sensor 241
- Low pressure sensor 241
- Evaporating temperature Te 241
- Condensing temperature Tc 243
- [With transmission] 246
- [Without transmission] 246
- Vout 0.5 ~ 3.5 V 249
- Pressure 0 ~ 1.7 MPa [247psi] 250
- Vout 0.5 ~ 3.5 V 250
- -3- Solenoid Valve 251
- 12345678 9 10 252
- 12345678 256
- Thermistor 257
- (liquid piping 257
- Linear Expansion Valve 257
- Lead wire 258
- -6- Inverter (TJMU-A) 260
- Check point 266
- Row B to Row E 266
- Installation direction 266
- L1 L2 L3 268
- SC-USC-RSC-SSC-TTB-N(Note) 269
- -6- Inverter (YJMU-A) 270
- Between Terminals 1 and 2 275
- Between Terminals 3 and 4 275
- Not to be short-circuited 275
- (Center value 75 ohm) 275
- -7- Control Circuit (TJMU-A) 277
- 1) PUHY-P72TJMU-A 279
- MA remote controller wiring 281
- (Non-polar 2 wire) 281
- Oudoor unit 281
- [5] Refrigerant Leak 283
- Compressor covers 286
- (right and left) 286
- 7SEG LED 290
- Alternate display 291
- Day count 291
- LED monitor display 292
- Current data 292
- Error history 302
- Data on indoor unit system 309
- Setting data 316
- Other types of data 332
- Issued in Feb. 2010 HWE09120 334
- Printed in Japan 334
Related products and manuals for Power adapters & inverters Mitsubishi Electric PURY-HP96T
(53 pages)
(20 pages)© 2020, manymanuals.com. All rights reserved. | 1.854 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals