Mitsubishi Electric PC36 Specifications Page 112
- Page / 300
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Startup Startup of servo amplifier series MR-J4-B(-RJ) and MR-J4W-B
5 - 8
5.3.3 Test operation
Before starting actual operation, perform test operation to make sure that the machine operates nor-
mally. Refer to section 5.3.1 for the power on and off methods of the servo amplifier.
NOTE If necessary, verify controller program by using motor-less operation. Refer to section 6.2.5 for the
motor-less operation
In this step, confirm that the servo amplifier and servo motor oper-
ate normally.
With the servo motor disconnected from the machine, use the test
operation mode and check whether the servo motor correctly
rotates at the slowest speed.
In this step, confirm that the servo motor correctly rotates at the
slowest speed under the commands from the controller.
Give a low speed command at first and check the rotation direc-
tion, etc. of the servo motor. If the machine does not operate in the
intended direction, check the input signal.
In this step, connect the servo motor with the machine and con-
firm that the machine operates normally under the commands
from the controller.
Give a low speed command at first and check the operation direc-
tion, etc. of the machine. If the machine does not operate in the
intended direction, check the input signal.
Check any problems with the servo motor speed, load ratio, and
other status display items with MR Configurator2.
Then, check automatic operation with the program of the controller.
Tab. 5-4: Test operation of the servo amplifier MR-J4-B
NOTE If there are any problems during startup, refer to the chapter “troubleshooting” in section 8.2, 8.3
and in the instruction manual of the respective servo amplifier.
Test operation of the servo motor
alone in JOG operation of test
operation mode
Test operation of the servo motor
alone by commands
Test operation with the servo motor
and machine connected
- MR-J4-A(-RJ)/A4(-RJ) 1
- MR-J4-B(-RJ)/B4(-RJ) 1
- MR-J4W-B 1
- About This Manual 3
- Safety Guidelines 7
- S001260E 12
- S001261E 12
- Typographic Conventions 13
- Table of Contents 15
- 1 Introduction 19
- 1.1.3 Servo motors 21
- 1.2 Environmental conditions 23
- 1.3 Terminology 24
- Control mode Description 25
- Introduction Terminology 26
- 2 Introduction of the devices 27
- MR-J4-500B4(-RJ) 28
- MR-J4-22KB(4)(-RJ) 28
- MR-J4W2-B 29
- MR-J4W3-B 29
- 2.5.1 200 V class 31
- 2.5.2 400 V class 33
- Front cover 36
- Setting tab 37
- 2.7 Rating plate 38
- 3.1 Rotatory servo motors 39
- 3.1.2 Rating plate 40
- HG-MR 3 42
- HG-SR 43
- Encoder connector 44
- Brake connector 44
- Power connector 44
- HG-JR 45
- HG-RR 3 47
- Zeichnung HG-RR153B.eps 48
- HG-UR 2 49
- 3.2 Linear servo motors 51
- LM-H3P - P - 52
- LM-U2P - M - 53
- LM-U2P2 - M - 2SS0 53
- Thermistor lead wire 54
- Power lead wire 54
- LM-F P - M - 1SS0 55
- LM-K2 P - M - 56
- 3.3.1 Model overview 57
- TM-RFM 58
- 4 Installation and wiring 59
- MR-J4-A Signalstecker.eps 63
- Only for MR-J4-A 69
- Only for MR-J4-A-RJ 69
- MR-J4-B Signalstecker.eps 70
- MR-J4W3-B Signalstecker.eps 73
- 4.3 Wiring the interfaces 76
- 4.3.3 Analog interfaces 78
- CN3CN3CN3 79
- 4.4.2 USB interface 80
- 4.6.1 MR-J4-B(-RJ) 83
- 4.6.2 MR-J4W-B 85
- MR-J4W-B_DIP switch SW2.eps 88
- 4.8 Servo motor 89
- Erdung MR-J4W.eps 90
- 4.9 Forced stop 93
- 4.10 Wiring examples 94
- 4.11.2 Wiring 102
- 4.11.3 Optional EMC filters 103
- 5Startup 105
- 5.2.2 Stop of operation 107
- 5.2.3 Test operation 108
- 5.2.5 Actual operation 109
- 5.2.4 Parameter setting 109
- 5.3.2 Stop of operation 111
- 5.3.3 Test operation 112
- MODE UP DOWN SET 113
- To/from previous table 120
- Option setting 120
- Positioning setting 120
- 6.1.6 Display examples 124
- 6.1.8 Alarm mode 125
- 6.1.9 Parameter mode 127
- 6.1.10 Test operation mode 129
- Operation Screen control 133
- Stop Click the “Stop” button 133
- 6.2.1 Overview 134
- 6.2.2 Scrolling display 135
- 6.2.3 Display sequence 136
- 6.2.4 Test operation 137
- Set SW2-1 to “OFF (down)” 141
- The decimal point flickers 141
- 6.3.1 Overview 142
- 6.3.2 Scrolling display 143
- 6.3.3 Display sequence 144
- 6.3.4 Test operation 145
- 2 3 4 5 6 147
- 7 Parameters 151
- Parameters MR-J4-A 154
- MR-J4-A Parameters 155
- 7.2 MR-J4-A-RJ 164
- MR-J4-A-RJ Parameters 167
- Parameters MR-J4-A-RJ 168
- 7.3 MR-J4-B(-RJ) 178
- MR-J4-B(-RJ) Parameters 181
- Parameters MR-J4-B(-RJ) 182
- 7.4 MR-J4W-B 189
- Parameters MR-J4W-B 192
- MR-J4W-B Parameters 193
- 7.5 Other parameters 200
- 8 Troubleshooting 201
- Series Servo Motor 207
- HG-SR HG-SR51, HG-SR52 207
- 8.4 Remedies for alarms 227
- 8.5 Remedies for warnings 228
- AAppendix 229
- ✔ — ✔✔——✔ 235
- ✔ — ✔✔— ✔ — 235
- 0 mV ✔✔✔✔✔✔✔ 235
- A.2.1 Status Display 245
- 0 mV ✔✔✔✔✔✔— 253
- A.3.1 Status display 266
- 0 mV ✔✔✔✔ 270
- A.4.1 Status display 280
- MIDDLE EAST REPRESENTATIVE 300
- AFRICAN REPRESENTATIVE 300
Related products and manuals for Split-system air conditioners Mitsubishi Electric PC36
(60 pages)
(28 pages)
(32 pages)
(144 pages)© 2020, manymanuals.com. All rights reserved. | 3.384 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals