Mitsubishi Electric UD8400U-W User Manual Page 34
- Page / 76
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
EN-34
INSTALLATION 1 menu
INSTALLATION 1
LENS LOCK
LENS SHIFT LOCK
ZOOM/FOCUS LOCK
LENS SHIFT RESET
OFF
OFF
COOLING CONDITION
TEST PATTERN
INSTALLATION 1
LAMP MODE
LAMP SELECT
STANDARD
1H/24H
LOW
OFF
STANDARD
0°
DUAL
LAMP RELAY
CROSS HATCH
HIGH ALTITUDE MODE
1
2
STANDBY MODE
IMAGE REVERSE
LENS LOCK
1
1
2
2
opt.
1
1
2
2
opt.
ENTER
OK
ITEM SETTING FUNCTION
LAMP MODE STANDARD Select this option when you want to view images in a well-lit room.
LOW Select to moderate the intensity of the lamp. The operating sound is reduced
and the lamp lifetime becomes longer.
LAMP SELECT DUAL
LAMP 1 and LAMP 2 illuminate.
SINGLE
The lamp with shorter operation time is automatically selected at power-on.
LAMP 1
LAMP 1 illuminates. (When it is broken or dead, LAMP 2 illuminates automatically.)
LAMP 2
LAMP 2 illuminates. (When it is broken or dead, LAMP 1 illuminates automatically.)
LAMP RELAY DUAL: OFF The LAMP RELAY doesn’t work.
1H/24H
/
2H/1W
Use to set the lamp relay interval. (See page 53.)
SINGLE:OFF The LAMP RELAY doesn’t work.
24H
/
1 WEEK
Use to set the lamp relay interval.
(See page 54.)
STANDBY MODE STANDARD Select this option when you control the projector via the LAN, REMOTE 1 IN,
and SERIAL OUT terminal during power standby.
LOW Select this option when you don’t control the projector via the LAN, REMOTE
1 IN, and SERIAL OUT terminal during power standby. This option disables
the LAN, REMOTE 1 IN, and SERIAL OUT terminal and reduces the power
consumption during the power standby.
IMAGE REVERSE OFF Select when viewing images from the front with the projector installed on the
fl oor.
MIRROR Select when viewing images projected from the behind of the screen with the
projector installed on the fl oor.
INVERT Select when viewing images projected from the behind of the screen with the
projector installed on the ceiling.
MIRROR INVERT Select when viewing images from the front with the projector installed on the
ceiling.
HIGH ALTITUDE MODE STANDARD
Select this option for normal use.
HIGH ALTITUDE Select this option for use at an altitude of 2000 to 2700 meters above the sea
level.
COOLING CONDITION 0° / 45° / 90° /
135°
/ 180° /
225°
/ 270° /
315°
The cooling condition changes according to the selected projection angle.
(See page 13.)
TEST PATTERN CROSS HATCH Select to show the test cross hatch pattern.
WHITE Select to show the maximum brightness image.
BLACK
Select to show the minimum brightness image.
H. COLOR BARS The horizontal color bar pattern is displayed.
V. COLOR BARS The vertical color bar pattern is displayed.
LENS LOCK ENTER
The LENS LOCK menu is displayed for the following settings.
ZOOM/FOCUS LOCK
ON / OFF Use to enable or cancel the FOCUS LOCK and ZOOM LOCK.
LENS SHIFT LOCK ON / OFF Use to enable or cancel the LENS SHIFT LOCK.
LENS SHIFT RESET OK
Use to reset the position of the lens to the factory setting.
• Regardless of the setting of LAMP MODE, the STANDARD lamp mode is activated by default whenever the projector is turned
on. When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW about 1 minute after turn-on.
• When the lamp mode is switched, the projected image may fl icker.
• Frequent switching of the lamp mode may damage the lamp.
• When using the projector for a long time, set LAMP RELAY.
• To cancel the test pattern, press any button other than the TEST PATTERN button on the remote control.
• While the lamps are being switched, an icon
is displayed to the right of the INSTALLATION 1 menu bar. While the icon is
being displayed, you cannot set LAMP SELECT and LAMP RELAY.
• After you switch the lamps and the newly selected lamp turns on, you cannot turn off the projector for approx. 1 minute.
Menu operation (continued)
- User Manual 1
- WARNING: 2
- CAUTION: 2
- Contents 3
- Important safeguards 4
- Preparing your projector 6
- Overview 7
- Bottom side 8
- Remote control 8
- Using the remote control 9
- Important: 10
- Setting up your projector 11
- Setup adjustment 12
- Setting the projector posture 13
- KEYSTONE 14
- SELECT : BLANK 14
- RESET KEYSTONE 14
- RESET LOWER RIGHT 15
- LOWER RIGHT 15
- Rear projection 18
- Viewing computer images 19
- B. Plugging the power cord 20
- VIDEO IN S-VIDEO IN IN-1 21
- D. Projecting images 22
- To stop projecting: 23
- Direct Power OFF 23
- AUTO POSITION button 24
- Setting of the resolution 24
- Setting the aspect ratio 25
- Viewing video images 26
- Equipment having an 27
- HDMI terminal 27
- To HDMI terminal 27
- B. Plugging in the power cord 28
- Menu operation 31
- Menu operation (continued) 32
- Adjusting projected images 42
- Color Enhancer 43
- SUPER RESOLUTION 44
- NCM−USER 44
- - USER menu 46
- Correction position marker 47
- Resetting the settings 48
- Initial network settings 49
- IP Settings 50
- Setting the control system 51
- NETWORK RESET 52
- Lamp relay 53
- Illuminating 54
- Advanced features 55
- Advanced features (continued) 56
- PROJECTOR ID 60
- GROUP ID 60
- COMPUTER1 61
- COMPUTER2 61
- VIDEO S-VIDEO 61
- Replacing the lamp 62
- EXECUTE LAMP 1 TIME RESET ? 63
- OK : ENTER CANCEL : MENU 63
- Maintenance 64
- Automatic cleaning fi lter 65
- Dust check window 66
- Troubleshooting 67
- Troubleshooting (continued) 68
- Indicators 71
- Specifi cations 72
- Specifi cations (continued) 73
- ITSUBISHI 76
- ELECTRIC CORPORATIO 76
Related products and manuals for Data projectors Mitsubishi Electric UD8400U-W
(39 pages)© 2020, manymanuals.com. All rights reserved. | 1.481 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals