Mitsubishi Electric UD8400U-W User Manual Page 51
- Page / 76
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
EN-51
6. When selecting OK, the setting is completed as
the IP ADDRESS stored. However, when selecting
CANCEL, the setting is completed without storing.
• When the setting you entered is correct, the
setting change dialog is displayed. After the
dialog disappears, the NETWORK menu is
displayed. If the entered content is not correct,
the NETWORK menu is displayed after an error
dialog is displayed.
• It may take some time to refl ect the settings.
Subnet Mask Settings
1. Display the IP CONFIG menu.
2. Press the S or T button to select SUBNET MASK.
SUBNET MASK
0. 0. 0. 0
3. Press the W or X button to select SET .
4. Press the ENTER button.
• SUBNET MASK screen appears.
SUBNET MASK
255 . 255 . 255 . 0
0
OK
CLEAR
DEL
CANCEL
12345678 9
← →
5. Enter the Subnet Mask.
• Refer to IP Address Settings for the detail of
entering.
6. When selecting OK, the setting is completed as
the Subnet Mask stored. However, when selecting
CANCEL, the setting is completed without storing.
• When the setting you entered is correct, the
setting change dialog is displayed. After the
dialog disappears, the NETWORK menu is
displayed. If the entered content is not correct,
the NETWORK menu is displayed after an error
dialog is displayed.
• It may take some time to refl ect the settings.
Default Gateway Settings
1. Display the IP CONFIG menu.
2. Press the S or T button to select DEFAULT
GATEWAY.
DEFAULT GATEWAY
0. 0. 0. 0
3. Press the W or X button to select SET .
4. Press the ENTER button.
• DEFAULT GATEWAY screen appears.
DEFAULT GATEWAY
10 . 132 . 1 . 1
0
OK
CLEAR
DEL
CANCEL
12345678 9
← →
5. Enter the Default Gateway.
• Refer to IP Address Settings for the detail of
entering.
6. When selecting OK, the setting is completed as the
Default Gateway stored. However, when selecting
CANCEL, the setting is completed without storing.
• When the setting you entered is correct, the
setting change dialog is displayed. After the
dialog disappears, the NETWORK menu is
displayed. If the entered content is not correct,
the NETWORK menu is displayed after an error
dialog is displayed.
• It may take some time to refl ect the settings.
Enabling or disabling the network
certifi cation
You can select whether or not to certify the network
communication using the network password.
• For details, contact your dealer.
(See page 32 for menu setting.)
1. Display the NETWORK menu.
2. Press the S or T button to select NET WORK
CERTIFICATION.
NETWORK CERTIFICATION
ON
3. Press the ENTER button.
• Confi rmation dialog appears.
NETWORK CERTIFICATION :
OK : ENTER CANCEL : MENU
ON
4. Press theW or X button to select ON or OFF .
5. Press the ENTER button.
• To cancel the setting, press the MENU button.
• It may take some time to refl ect the settings.
Setting the control system
Set the control system.
(See page 32 for menu setting.)
1. Display the NETWORK menu.
2. Press the S or T button to select CONTROL
SYSTEM.
CONTROL SYSTEM
STANDARD
3. Press the ENTER button.
CONTROL SYSTEM :
OK : ENTER CANCEL : MENU
STANDARD
4. Press theW or X button to select STANDARD ,
AMX , or CRESTRON .
STANDARD
Select this setting when using ProjectorView
Global+ or ProjectorView.
AMX
Select this setting when using the controller of
AMX. (See page 58.)
CRESTRON
Select this setting when using the controller or
software of Crestron Electronics, Inc. (See page 58.)
Important:
• PJLink™ works regardless of the setting of
CONTROL SYSTEM.
5. Press the ENTER button.
Initial network settings (continued)
- User Manual 1
- WARNING: 2
- CAUTION: 2
- Contents 3
- Important safeguards 4
- Preparing your projector 6
- Overview 7
- Bottom side 8
- Remote control 8
- Using the remote control 9
- Important: 10
- Setting up your projector 11
- Setup adjustment 12
- Setting the projector posture 13
- KEYSTONE 14
- SELECT : BLANK 14
- RESET KEYSTONE 14
- RESET LOWER RIGHT 15
- LOWER RIGHT 15
- Rear projection 18
- Viewing computer images 19
- B. Plugging the power cord 20
- VIDEO IN S-VIDEO IN IN-1 21
- D. Projecting images 22
- To stop projecting: 23
- Direct Power OFF 23
- AUTO POSITION button 24
- Setting of the resolution 24
- Setting the aspect ratio 25
- Viewing video images 26
- Equipment having an 27
- HDMI terminal 27
- To HDMI terminal 27
- B. Plugging in the power cord 28
- Menu operation 31
- Menu operation (continued) 32
- Adjusting projected images 42
- Color Enhancer 43
- SUPER RESOLUTION 44
- NCM−USER 44
- - USER menu 46
- Correction position marker 47
- Resetting the settings 48
- Initial network settings 49
- IP Settings 50
- Setting the control system 51
- NETWORK RESET 52
- Lamp relay 53
- Illuminating 54
- Advanced features 55
- Advanced features (continued) 56
- PROJECTOR ID 60
- GROUP ID 60
- COMPUTER1 61
- COMPUTER2 61
- VIDEO S-VIDEO 61
- Replacing the lamp 62
- EXECUTE LAMP 1 TIME RESET ? 63
- OK : ENTER CANCEL : MENU 63
- Maintenance 64
- Automatic cleaning fi lter 65
- Dust check window 66
- Troubleshooting 67
- Troubleshooting (continued) 68
- Indicators 71
- Specifi cations 72
- Specifi cations (continued) 73
- ITSUBISHI 76
- ELECTRIC CORPORATIO 76
Related products and manuals for Data projectors Mitsubishi Electric UD8400U-W
(39 pages)© 2020, manymanuals.com. All rights reserved. | 0.199 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals