Mitsubishi Electric UD8400U-W User Manual Page 61
- Page / 76
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
EN-61
Control by a control panel, etc.
When installing the projector in a place where the remote control signals cannot reach the projector, you can control
the projector using a control panel or other device connected to the REMOTE 1 IN terminal.
ON
POWER
COMPUTER1
OFF
ON
BLANK
OFF
Remote control
External contact
control
COMPUTER2
VIDEO S-VIDEO
DVI
Projector
Control
p
anel
Controllable functions
• Switching between remote control and external
control
• Switching input signals
• Power-on and power-off
• BLANK-on and BLANK-off
Important:
• To control the projector using a control panel, set
STANDBY MODE in the INSTALLATION 1 menu to
STANDARD. When it is LOW, you cannot control
the projector.
Connection
• Make sure that the power supplies of the projector
and control panel are off.
To REMOTE 1 IN
RS-232C cable (option)
Control panel
1. Connect one end of an RS-232C cable to the
REMOTE 1 IN terminal on the projector.
2. Connect the other end of the RS-232C cable to the
control panel.
Pin functions (defaults)
REMOTE 1 IN (D-SUB 9-pin)
Pin No.
Signal Open (H) Short (L)
1 GND – GND
2 POWER OFF ON
3 Input – COMPUTER1
4 Input – COMPUTER2
5 Input – VIDEO
6 Input – S-VIDEO
7 Input – DVI
8 BLANK OFF ON
9 ON/OFF Valid (Remote control) Invalid (External contact control)
• You can change the functions of PIN 2 to PIN 8
using REMOTE 1 MODE in the INSTALLATION 2
menu. See page 35.
Important:
• To reset the pin functions to the defaults, set
REMOTE 1 MODE in the INSTALLATION 2 to
RESET.
Contact control
By short-circuiting Pin No. 1 and Pin No. 9, you can
control the projector using a control panel or other
device.
• When you short-circuit Pin No. 1 and Pin No. 9, the
following functions cannot be used:
∙ POWER and BLANK of the remote control and
the projector
∙ RS-232C commands and network functions
corresponding to the above-mentioned
functions
∙ REMOTE 1 MODE, AUTO POWER ON and
AUTO POWER OFF in the INSTALLATION 2
menu.
∙ STANDBY MODE in the INSTALLATION 1 menu.
Input switching control
By short-circuiting any of Pin No. 3 to Pin No. 7, you
can switch the input using a control panel or other
device.
• When short-circuiting any of Pin No. 3 to Pin No. 7,
you cannot use the following functions.
∙ POWER, BLANK, COMPUTER 1, COMPUTER
2, VIDEO, S-VIDEO, DVI, HDMI, and SDI of the
remote control and the projector
∙ RS-232C commands and network functions
corresponding to the above-mentioned
functions
POWER control
By short-circuiting or open-circuiting Pin No. 2, you
can turn on or off the power using a control panel or
other device.
BLANK control
By short-circuiting or open-circuiting Pin No. 8, you
can turn on or off the BLANK function using a control
panel or other device.
Advanced features (continued)
- User Manual 1
- WARNING: 2
- CAUTION: 2
- Contents 3
- Important safeguards 4
- Preparing your projector 6
- Overview 7
- Bottom side 8
- Remote control 8
- Using the remote control 9
- Important: 10
- Setting up your projector 11
- Setup adjustment 12
- Setting the projector posture 13
- KEYSTONE 14
- SELECT : BLANK 14
- RESET KEYSTONE 14
- RESET LOWER RIGHT 15
- LOWER RIGHT 15
- Rear projection 18
- Viewing computer images 19
- B. Plugging the power cord 20
- VIDEO IN S-VIDEO IN IN-1 21
- D. Projecting images 22
- To stop projecting: 23
- Direct Power OFF 23
- AUTO POSITION button 24
- Setting of the resolution 24
- Setting the aspect ratio 25
- Viewing video images 26
- Equipment having an 27
- HDMI terminal 27
- To HDMI terminal 27
- B. Plugging in the power cord 28
- Menu operation 31
- Menu operation (continued) 32
- Adjusting projected images 42
- Color Enhancer 43
- SUPER RESOLUTION 44
- NCM−USER 44
- - USER menu 46
- Correction position marker 47
- Resetting the settings 48
- Initial network settings 49
- IP Settings 50
- Setting the control system 51
- NETWORK RESET 52
- Lamp relay 53
- Illuminating 54
- Advanced features 55
- Advanced features (continued) 56
- PROJECTOR ID 60
- GROUP ID 60
- COMPUTER1 61
- COMPUTER2 61
- VIDEO S-VIDEO 61
- Replacing the lamp 62
- EXECUTE LAMP 1 TIME RESET ? 63
- OK : ENTER CANCEL : MENU 63
- Maintenance 64
- Automatic cleaning fi lter 65
- Dust check window 66
- Troubleshooting 67
- Troubleshooting (continued) 68
- Indicators 71
- Specifi cations 72
- Specifi cations (continued) 73
- ITSUBISHI 76
- ELECTRIC CORPORATIO 76
Related products and manuals for Data projectors Mitsubishi Electric UD8400U-W
(39 pages)© 2020, manymanuals.com. All rights reserved. | 3.221 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals