Mitsubishi Electric UD8400U-W User Manual Page 59
- Page / 76
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
EN-59
Connection
For details of the connection, see “LAN control UTILITY operation manual” in the CD-ROM.
When STANDBY MODE of the INSTALLATION 1 menu of the projector is set to LOW, the LAN network is disabled.
To enable the LAN network, set STANDBY MODE to STANDARD. (See page 34 .)
Confi gure the initial network settings fi rst.
You can confi gure the initial settings using the projector menu (see pages 49 to 52) or ProjectorView Global+. For
details of ProjectorView Global+, see “LAN control UTILITY operation manual” in the CD-ROM.
Using the User Manual
The User Manual for LAN Control Utility is prepared in the Portable Document Format (PDF) in the CD-ROM.
Opening the User Manual:
1. Load the CD-ROM into the CD-ROM drive.
2. Open CD-ROM “PROJECTOR.”
3. Double-click on “MANUAL_LAN.HTML” within the CD-ROM. A language selection list for the User Manual will be
displayed.
4. Move the mouse pointer to the desired language and click.
PJLink™ supported commands
The table below shows commands to control the projector using the PJLink™ protocol.
Command Description Remark (Parameter)
POWR Power control 0 = Standby
1 = Power on
POWR? Inquiry about the power state 0 = Standby
1 = Power on
2 = Cooling down
3 = Warming up
INPT Input switching 11 = COMPUTER1 12 = COMPUTER2
21 = VIDEO 22 = S-VIDEO
31 = HDMI 32 = DVI 33 = SDI
INPT? Inquiry about input switching
AVMT Mute control 30 = Video mute disable
31 = Video mute enable
AVMT? Inquiry about the mute state
ERST? Inquiry about the error state 1st byte: Fan error, 0 or 2
2nd byte: Lamp error, 0 to 2
3rd byte: Temperature error, 0 or 2
4th byte: Cover open error, 0 or 2
5th byte: Always 0
6th byte: Other error, 0 or 2
0 to 2 mean as follows:
0 = No error detected, 1 = Warning, 2 = Error
LAMP? Inquiry about the lamp state
1st value (1 to 5 digits): Cumulative LAMP 1 operating time (This item
shows a lamp operating time (hour) calculated
based on that LAMP MODE is LOW.)
2nd value: 0 = Lamp off, 1 = Lamp on
3rd value (1 to 5 digits): Cumulative LAMP 2 operating time (This item
shows a lamp operating time (hour) calculated
based on that LAMP MODE is LOW.)
4th value: 0 = Lamp off, 1 = Lamp on
INST? Inquiry about the available inputs The following value is returned.
“11 12 21 22 31 32 33”
NAME? Inquiry about the projector name The projector name set on the NETWORK menu or the ProjectorView
Setup window is returned.
INF1? Inquiry about the manufacturer name “MITSUBISHI” is returned.
INF2? Inquiry about the model name “UD8400U” is returned.
INF0? Inquiry about other information No other information is available. No parameter is returned.
CLSS? Inquiry about the class information “1” is returned.
• This projector is fully compliant to the specifi cations of JBMIA PJLink™ Class 1. It supports all the commands defi ned by
PJLink™ Class 1, and the compliance has been verifi ed with the PJLink™ standard specifi cations Version 1.0.
Advanced features (continued)
- User Manual 1
- WARNING: 2
- CAUTION: 2
- Contents 3
- Important safeguards 4
- Preparing your projector 6
- Overview 7
- Bottom side 8
- Remote control 8
- Using the remote control 9
- Important: 10
- Setting up your projector 11
- Setup adjustment 12
- Setting the projector posture 13
- KEYSTONE 14
- SELECT : BLANK 14
- RESET KEYSTONE 14
- RESET LOWER RIGHT 15
- LOWER RIGHT 15
- Rear projection 18
- Viewing computer images 19
- B. Plugging the power cord 20
- VIDEO IN S-VIDEO IN IN-1 21
- D. Projecting images 22
- To stop projecting: 23
- Direct Power OFF 23
- AUTO POSITION button 24
- Setting of the resolution 24
- Setting the aspect ratio 25
- Viewing video images 26
- Equipment having an 27
- HDMI terminal 27
- To HDMI terminal 27
- B. Plugging in the power cord 28
- Menu operation 31
- Menu operation (continued) 32
- Adjusting projected images 42
- Color Enhancer 43
- SUPER RESOLUTION 44
- NCM−USER 44
- - USER menu 46
- Correction position marker 47
- Resetting the settings 48
- Initial network settings 49
- IP Settings 50
- Setting the control system 51
- NETWORK RESET 52
- Lamp relay 53
- Illuminating 54
- Advanced features 55
- Advanced features (continued) 56
- PROJECTOR ID 60
- GROUP ID 60
- COMPUTER1 61
- COMPUTER2 61
- VIDEO S-VIDEO 61
- Replacing the lamp 62
- EXECUTE LAMP 1 TIME RESET ? 63
- OK : ENTER CANCEL : MENU 63
- Maintenance 64
- Automatic cleaning fi lter 65
- Dust check window 66
- Troubleshooting 67
- Troubleshooting (continued) 68
- Indicators 71
- Specifi cations 72
- Specifi cations (continued) 73
- ITSUBISHI 76
- ELECTRIC CORPORATIO 76
Related products and manuals for Data projectors Mitsubishi Electric UD8400U-W
(39 pages)© 2020, manymanuals.com. All rights reserved. | 1.773 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals