Mitsubishi Electric FR-E700 Instruction Manual Page 99
- Page / 286
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Parameter listParameter list
92
Parameter List
5
PARAMETERS
— 244 Cooling fan operation selection 0, 1 1 1 213 244 34 B4 2
Slip
compensation
245 Rated slip 0 to 50%, 9999 0.01% 9999 119 245 35 B5 2
246 Slip compensation time constant 0.01 to 10s 0.01s 0.5s 119 246 36 B6 2
247
Constant-power range slip
compensation selection
0, 9999 1 9999 119 247 37 B7 2
— 249 Earth (ground) fault detection at start 0, 1 1 0 190 249 39 B9 2
— 250 Stop selection
0 to 100s,
1000 to 1100s,
8888, 9999
0.1s 9999 157 250 3A BA 2
— 251 Output phase loss protection selection 0, 1 1 1 190 251 3B BB 2
Life diagnosis
255 Life alarm status display (0 to 15) 1 0 214 255 3F BF 2
256 Inrush current limit circuit life display (0 to 100%) 1% 100% 214 256 40 C0 2
257 Control circuit capacitor life display (0 to 100%) 1% 100% 214 257 41 C1 2
258 Main circuit capacitor life display (0 to 100%) 1% 100% 214 258 42 C2 2
259 Main circuit capacitor life measuring 0, 1 (2, 3, 8, 9) 1 0 214 259 43 C3 2
Power
failure
stop
261 Power failure stop selection 0, 1, 2 1 0 186 261 45 C5 2
— 267 Parameter for manufacturer setting. Do not set. 267 Parameter for manufacturer setting. Do not set.
— 268 Monitor decimal digits selection 0, 1, 9999 1 9999 176 268 4C CC 2
— 269 Parameter for manufacturer setting. Do not set. 269 Parameter for manufacturer setting. Do not set.
— 270 Stop-on contact control selection 0, 1 1 0 158 270 4E CE 2
Stop-on
contact
control
275
Stop-on contact excitation current low-
speed multiplying factor
0 to 300%, 9999 0.1% 9999 158
275 53 D3 2
276
PWM carrier frequency at stop-on
contact
0 to 9, 9999 1 9999 158 276 54 D4 2
— 277
Stall prevention operation current
switchover
0, 1 1 0 120 277 55 D5 2
Brake sequence
function
278 Brake opening frequency 0 to 30Hz 0.01Hz 3Hz 160 278 56 D6 2
279 Brake opening current 0 to 200% 0.1% 130% 160 279 57 D7 2
280 Brake opening current detection time 0 to 2s 0.1s 0.3s 160 280 58 D8 2
281 Brake operation time at start 0 to 5s 0.1s 0.3s 160 281 59 D9 2
282 Brake operation frequency 0 to 30Hz 0.01Hz 6Hz 160 282 5A DA 2
283 Brake operation time at stop 0 to 5s 0.1s 0.3s 160 283 5B DB 2
Droop
control
286 Droop gain 0 to 100% 0.1% 0% 210 286 5E DE 2
287 Droop filter time constant 0 to 1s 0.01s 0.3s 210 287 5F DF 2
— 292 Automatic acceleration/deceleration 0, 1, 7, 8, 11 1 0 140 292 64 E4 2
— 293
Acceleration/deceleration separate
selection
0 to 2 1 0 140 293 65 E5 2
— 295 Magnitude of frequency change setting 0, 0.01, 0.1, 1, 10 0.01 0 226 295 67 E7 2
Password
function
296 Password lock level
0 to 6, 99, 100 to 106,
199, 9999
1 9999 199 296 68 E8 2
297 Password lock/unlock
(0 to 5), 1000 to 9998,
9999
1 9999 199 297 69 E9 2
— 298 Frequency search gain 0 to 32767, 9999 1 9999 180 298 6A EA 2
— 299
Rotation direction detection selection
at restarting
0, 1, 9999 1 0 180 299 6B EB 2
Digital output
313 RX9 function selection
0, 1, 3, 4, 7, 8, 11 to 16,
20, 25, 26, 46, 47, 64,
68, 80, 81
90, 91, 93,
95, 96, 98, 99, 100, 101,
103, 104, 107, 108,
111 to 116, 120, 125,
126, 146, 147, 164, 168,
180
181 190, 191, 193,
195, 196, 198, 199,
9999
1 9999 167 313 0D 8D 3
314 RXA function selection 1 9999 167 314 0E 8E 3
315 RXB function selection 1 9999 167 315 0F 8F 3
Func-
tion
Parameter
Name Setting Range
Minimum
Setting
Increments
Initial
Value
Refer
to
Page
Customer
Setting
Parameter
Instruction Code Control Mode-based Correspondence Parameter
Read Write Extended Clear
All clear
V/F
V/F
V/F
AD
MFVC
AD
MFVC
AD
MFVC
GP
MFVC
GP
MFVC
GP
MFVC
- FR-E720-0.1KNC to 15KNC 1
- FR-E740-0.4KNC to 15KNC 1
- FR-E720S-0.1KNC to 2.2KNC 1
- 1. Electric Shock Prevention 2
- 2. Fire Prevention 2
- 3.Injury Prevention 2
- CONTENTS 4
- 5 PARAMETERS 79 6
- 6 TROUBLESHOOTING 231 8
- 8 SPECIFICATIONS 265 9
- APPENDIX 273 10
- 1 OUTLINE 12
- E740 2.2 13
- (Refer to page 266) 14
- (Refer to page 4) 14
- (Refer to page 40) 14
- (Refer to page 220) 14
- 1.2.1 Peripheral devices 15
- MCCB INV 15
- 1.3.1 Front cover 16
- 1) 2) 3) 17
- 1.3.2 Wiring cover 18
- (1) Temperature 19
- (2) Humidity 19
- (3) Dust, dirt, oil mist 20
- (6) Highland 20
- (7) Vibration, impact 20
- ∗1, ∗2 ∗1∗1, ∗2 22
- (2) Above inverter 23
- 2 WIRING 24
- 2.1 Wiring 25
- Three-phase 200V class 26
- Three-phase 400V class 27
- Single-phase 200V class 27
- (1) Applicable cable size 28
- Inverter 29
- 500m or less 30
- 300m+300m=600m 30
- (1) Input signal 31
- (2) Output signal 31
- (3) Communication 31
- 0 to 0.5m 32
- (4) Wiring instructions 33
- 2.3.4 Safety stop function 35
- ∗3 SAFE2∗3 36
- (0.4K or higher) 37
- To the brake unit 39
- To a resistor 39
- 1/L1 5/L3 39
- 2/T1 6/T3 39
- Remove the jumper 40
- PRECAUTIONS FOR USE 42
- OF THE INVERTER 42
- 3.1 EMC and leakage currents 43
- EMC and leakage currents 44
- Noise propagated through 45
- Noise from earthing 45
- (grounding) cable 45
- 3.1.3 Power supply harmonics 47
- Single-phase power input 50
- Measures 52
- Positive logic Negative logic 56
- CC-LINK COMMUNICATION 58
- FUNCTION 58
- 4.2 CC-Link version 59
- QJ61BT11N 60
- *2 FR-E700-NC 61
- Model Manufacturer 62
- (4) Crimping the plug cover 63
- 4.4 Function overview 65
- Function overview 66
- 4.5 I/O signal list 67
- I/O signal list 68
- (1) Remote I/O (32 points) 70
- (2) Remote register 70
- Details of I/O signals 71
- *1 0.01Hz/1 77
- Programming examples 78
- : ON, : OFF, : Flicker 86
- Running frequency 91
- Output current 91
- Output voltage 91
- (Refer to page 82) 92
- (Refer to page 229) 92
- 5.1.4 Setting dial push 94
- 113 0 00 80 0 95
- 135 707 87 0 95
- 135 8 08 88 0 95
- 154 12 0C 8C 0 95
- 135 44 2C AC 0 96
- 90, 91, 93 98
- 181190, 191, 193 98
- 90, 91, 95 98
- 181 190, 191, 195 98
- 90, 91, 93 99
- 181 190, 191, 193 99
- Parameter listParameter list 100
- PARAMETERS 100
- Selection of operation mode 106
- Refer to page 196 107
- Refer to page 224 107
- ∗ Continued 112
- ∗1 Allowed Disallowed 113
- ∗2 Allowed Allowed 113
- 5.5 Control mode 114
- Control mode 115
- Test run 118
- Load torque 119
- (1) Block diagram 123
- (Refer to page 165) 125
- Limiting the output frequency 127
- 5.8 V/F pattern 129
- V/F pattern 130
- 14 Load pattern selection 131
- Refer to page 163 134
- Remote function selection 135
- Refer to page 135 137
- Pr. 180 to Pr. 184 137
- 13 Starting frequency 141
- 571 Holding time at a start 141
- Operation time (min) 145
- Operation time (s) 145
- (1) Set the motor to be used 147
- Parameter 149
- ∗1 Direct Input Value ∗2 150
- (2) Setting 151
- Flickering 152
- Error Cause Remedy 153
- Iq =torque current, I 155
- =rated current, I 155
- =no load current 155
- CAUTION 158
- Refer to page 167 159
- 250 Stop selection 160
- (1) Operation example 161
- (4) Protective functions 165
- Parameters referred to 165
- Refer to 167
- Refer to page 157) 168
- Pr.250 Stop selection 168
- Refer to page 157 168
- (1) Output current detection 175
- Refer to page 167 176
- ∗1 Machine speed ∗1 178
- ∗1, ∗2 1h 23 179
- (terminal Y0) 181
- Center line is always ON 181
- Pr. 37 Speed display 182
- Refer to page 175 182
- Retry failure example 191
- Retry success example 191
- 5.17 Energy saving operation 194
- (1) Reset selection 197
- (2) PU stop selection 197
- Parameter write selection 199
- Refer to page 197 203
- 15 Jog frequency 204
- (2) PID action overview 207
- (7) Adjustment procedure 211
- (8) Calibration example 211
- (1) Droop control 213
- Pr. 8 Deceleration time 215
- Refer to page 135 215
- 5.21 Useful functions 216
- Useful functions 217
- Pr. 503 Maintenance timer 222
- Refer to page 217 222
- USB cable 223
- USB connector 223
- A connector 224
- Connector for amplifier 224
- 888 Free parameter 1 225
- 889 Free parameter 2 225
- When Pr. 295 = "1" 229
- 1 click 1 click 1 click 229
- Setting Description 230
- (2) Clearing procedure 233
- TROUBLESHOOTING 234
- Causes and corrective actions 237
- 6.5.1 Motor does not start 247
- PRECAUTIONS FOR 254
- MAINTENANCE AND INSPECTION 254
- 7.1.1 Daily inspection 255
- 7.1.2 Periodic inspection 255
- Inspection items 256
- 7.1.6 Cleaning 258
- 7.1.7 Replacement of parts 258
- Fan connection 259
- Fan cover 259
- AIR FLOW 260
- Three-phase 262
- To the motor 262
- Three-phase power input 262
- 7.2.1 Measurement of powers 264
- 7.2.3 Measurement of currents 265
- 7.2.8 Pressure test 266
- SPECIFICATIONS 268
- 8.1 Rating 269
- SPECIFICATIONS 270
- 8.2 Common specifications 271
- Outline dimension drawings 272
- APPENDIX 276
- Item FR-E500 (N) FR-E700 (NC) 277
- Appendix 3 Index 279
- REVISIONS 283
- E700-NC Series 284
- Instruction Manual Supplement 284
- General precaution 285
- Motor overload protection 285
Related products and manuals for Power adapters & inverters Mitsubishi Electric FR-E700
(14 pages)
(20 pages)© 2020, manymanuals.com. All rights reserved. | 2.873 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals