Mitsubishi Electric FR-E540 Instruction Manual Page 120
- Page / 217
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
PARAMETERS
107
<Function/operation changed by switching on-off the X12 (MRS) signal>
Operating Condition
Operation
mode
Status
X12 (MRS)
Signal
Operation
Mode
(Note 4)
Operating Status Parameter Write
Switching
to PU
Operation
Mode
During stop
ON
→
OFF
(Note 3)
During stop Allowed
→
disallowed Disallowed
PU
During
operation
ON
→
OFF
(Note 3)
External
If external operation
frequency setting and start
signal are entered,
operation is performed in
that status.
Allowed
→
disallowed Disallowed
OFF
→
ON Disallowed
→
disallowed Allowed
During stop
ON
→
OFF
During stop
Disallowed
→
disallowed Disallowed
OFF
→
ON
During operation
→
output stop
Disallowed
→
disallowed Disallowed
External
During
operation
ON
→
OFF
External
Output stop
→
During operation
Disallowed
→
disallowed Disallowed
Note: 1. When the Pr. 79 setting is 7 and the PU operation interlock signal is OFF, network operation such
as computer link cannot be used.
2. If the X12 (MRS) signal is on, the operation mode cannot be switched to the PU operation mode
when the start signal (STF, STR) is on.
3. The operation mode switches to the external operation mode independently of whether the start
signal (STF, STR) is on or off. Therefore, the motor is run in the external operation mode when
the X12 (MRS) signal is switched off with either of STF and STR on.
4. When an alarm occurs, the inverter can be reset by pressing the
STOP
RESET
key of the operation
panel.
5. When the MRS signal is used as the PU interlock signal, switching the MRS signal on and
rewriting the Pr. 79 value to other than 7 in the PU operation mode causes the MRS signal to
provide the ordinary MRS function (output stop). Also, as soon as 7 is set in Pr. 79, the MRS
signal acts as a PU interlock signal.
6. When the MRS signal is used as the PU external interlock signal, the signal logic conforms to the
Pr. 17 setting. When Pr. 17 = 2, read ON for OFF and OFF for ON in the above explanation.
(
3
)
Operation mode external signal switching function
1) Preparation
Set "8" (switching to other than external operation mode) in Pr. 79. Using any of Pr. 180 to Pr. 186 (input
terminal function selection), allocate the terminal used to input the X16 (PU-external operation switching)
signal.
Refer to page 138 for Pr. 180 to Pr. 186 (input terminal function selection).
Note: When terminal assignment is changed using Pr. 180 to Pr. 186, the other functions may be affected.
Check the functions of the corresponding terminals before making setting.
2) Function
When the X16 signal is switched on in the PU operation mode, the operation mode is forcibly changed to
the external operation mode. When the X16 signal is switched off in the external operation mode, the
operation mode is changed to the PU operation mode. When the X16 signal is switched off during network
operation such as computer link, the operation mode is changed to the PU operation mode as soon as the
switch-over command to the external operation mode is sent from the computer. Note that this switch-over
may only be made while the inverter is at a stop and cannot be made during operation.
X16 Signal Operation Mode
ON External operation mode (cannot be changed to the PU operation mode)
OFF PU operation mode (cannot be changed to the external operation mode)
4
- FR-F520-0.75K to 55K 1
- FR-F540-0.75K to 55K(-EC) 1
- FR-F520-11K to 55K-NA 1
- FR-F540-11K to 55K-NA 1
- SAFETY INSTRUCTIONS 3
- 1. Electric Shock Prevention 3
- 2. Fire Prevention 3
- 3. Injury Prevention 3
- 4. Additional instructions 4
- (2) Wiring 4
- (3) Trial run 4
- (4) Operation 4
- (5) Emergency stop 5
- (7) Disposing of the inverter 5
- (8) General instructions 5
- CONTENTS 6
- Contents 6
- 6 SPECIFICATIONS 184 9
- 7 OPTIONS 192 9
- APPENDICES 195 9
- CHAPTER 1 10
- 1.1 Pre-Operation Information 11
- 1.2 Basic Configuration 12
- 1.3 Structure 13
- Front cover 14
- Inverter 14
- INSTALLATION AND WIRING 17
- 2.1 Installation 18
- 2.2 Wiring 20
- Notes on Grounding 24
- EC version 30
- NA and Japanese version 30
- Twin contact 38
- Low-level signal contacts 38
- 2.3 Other wiring 39
- 2.3.6 Peripheral devices 48
- 2.3.9 Earthing (EC version) 53
- CHAPTER 3 54
- OPERATION/CONTROL 54
- 3.1 Pre-Operation Information 55
- 3.1.2 Power on 57
- 3.2 Operation Panel 58
- 3.2.3 Monitoring 59
- 3.2.4 Frequency setting 59
- 3.2.6 Operation mode 61
- 3.2.7 Help mode 61
- 3.2.8 Copy mode 63
- 3.3.1 Parameter checking 64
- Simple mode parameter 65
- 3.3.2 Main parameter settings 66
- 3.4 Operation 68
- CONTROL PANEL 69
- 3.4.3 PU operation mode 70
- 3.4.4 Combined operation mode 71
- CHAPTER 4 72
- PARAMETERS 72
- 4 PARAMETERS 73
- 4.1 Parameter List 73
- Output frequency (Hz) 81
- Output voltage 81
- (Pr. 52 to Pr. 54, Pr. 158) 99
- With alarm 100
- PARAMETERS 101
- 4.2.29 Applied motor (Pr. 71) 110
- 4.2.31 Voltage input (Pr. 73) 112
- (Pr. 75) 113
- Time (Minute) 131
- Minute (Second) 131
- (Pr. 135 to Pr. 139) 140
- Set time (s) 149
- Overload status (OL output) 149
- OL output signal 149
- (Pr. 170, Pr. 171) 151
- Pr. 516 Pr. 504 163
- Pr. 502 + Pr. 503 163
- (Pr. 902 to Pr. 905) 170
- MON EXT PU 172
- PROTECTIVE FUNCTIONS 176
- 5 PROTECTIVE FUNCTIONS 177
- 5.1 Errors (Alarms) 177
- (2) Minor fault 184
- (3) Warnings 184
- 5.1.4 Alarm code output 187
- 5.1.5 Resetting the inverter 187
- 5.2 Troubleshooting 188
- 5.3.2 Check items 190
- 5.3.3 Periodic inspection 190
- 5.3.5 Pressure test 191
- <Preparation> 193
- <Checking method> 193
- Fan cover 194
- Fan connectors 194
- <Example: FR-F540-5.5K> 194
- 5.3.8 Inverter replacement 195
- CHAPTER 6 198
- SPECIFICATIONS 198
- 6 SPECIFICATIONS 199
- 6.1 Standard Specifications 199
- 6.1.2 Common specifications 201
- 95 (3.74) 203
- CHAPTER 7 207
- 7 OPTIONS 208
- 7.1 Option List 208
- • Inboard options 210
- APPENDICES 211
- Appendix 1 Data Code List 212
- REVISIONS 217
Related products and manuals for Power adapters & inverters Mitsubishi Electric FR-E540
(57 pages)© 2020, manymanuals.com. All rights reserved. | 0.684 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals