Mitsubishi Electric FR-E540 Instruction Manual Page 131
- Page / 217
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
PARAMETERS
118
No. Item
Instruction
Code
Description
Number
of Data
Digits
Read H6C
When setting the programmed operation
(data code H3D to H5A, HBD to HDA)
parameter
H00: Time
H01: Time
H02: Rotation direction
63
3
B
Time (Minute)
Minute (Second)
13
Second
parameter
changing
(Code
FF = 1)
Write HEC
When setting the bias/gain (data code H5E to H61, HDE to HE1)
parameter
H00: Offset/gain
H01: Analog
H02: Analog value of terminal
2 digits
REMARKS
Once the HFF, HEC or HF3 instruction code is written, the set value is held, but is reset to 0 when the
inverter is reset or all clear is performed.
<Error Code List>
The corresponding error code in the following list is displayed if an error is detected in any communication
request data form the computer.
Error
Code
Item Definition Inverter Operation
H0 Computer NAK error
The number of errors consecutively detected in communication
request data from the computer is greater than allowed number
of retry times.
H1 Parity error The parity check result does not match the specified parity.
H2 Sum check error
The sum check code in the computer does not match that of the
data received by the inverter.
H3 Protocol error
Data received by the inverter is in the wrong protocol, data
receive is not completed within the given time, or CR and LF are
not as set in the parameter.
H4 Framing error The stop bit length is not as specified.
H5 Overrun error
New data has been sent by the computer before the inverter
completes receiving the preceding data.
Brought to an alarm stop
(E.OPT) if error occurs
continuously more than
the allowable number of
retry times.
H6
H7 Character error
The character received is invalid (other than 0 to 9, A to F,
control code).
Does not accept receive
data but is not brought to
alarm stop.
H8
H9
HA Mode error
Parameter write was attempted in other than the computer link
operation mode or during inverter operation.
HB
Instruction code
error
The specified command does not exist.
HC Data range error
Invalid data has been specified for parameter write, frequency
setting, etc.
Does not accept or
receive data but is not
brought to alarm stop.
HD
HE
HF
- FR-F520-0.75K to 55K 1
- FR-F540-0.75K to 55K(-EC) 1
- FR-F520-11K to 55K-NA 1
- FR-F540-11K to 55K-NA 1
- SAFETY INSTRUCTIONS 3
- 1. Electric Shock Prevention 3
- 2. Fire Prevention 3
- 3. Injury Prevention 3
- 4. Additional instructions 4
- (2) Wiring 4
- (3) Trial run 4
- (4) Operation 4
- (5) Emergency stop 5
- (7) Disposing of the inverter 5
- (8) General instructions 5
- CONTENTS 6
- Contents 6
- 6 SPECIFICATIONS 184 9
- 7 OPTIONS 192 9
- APPENDICES 195 9
- CHAPTER 1 10
- 1.1 Pre-Operation Information 11
- 1.2 Basic Configuration 12
- 1.3 Structure 13
- Front cover 14
- Inverter 14
- INSTALLATION AND WIRING 17
- 2.1 Installation 18
- 2.2 Wiring 20
- Notes on Grounding 24
- EC version 30
- NA and Japanese version 30
- Twin contact 38
- Low-level signal contacts 38
- 2.3 Other wiring 39
- 2.3.6 Peripheral devices 48
- 2.3.9 Earthing (EC version) 53
- CHAPTER 3 54
- OPERATION/CONTROL 54
- 3.1 Pre-Operation Information 55
- 3.1.2 Power on 57
- 3.2 Operation Panel 58
- 3.2.3 Monitoring 59
- 3.2.4 Frequency setting 59
- 3.2.6 Operation mode 61
- 3.2.7 Help mode 61
- 3.2.8 Copy mode 63
- 3.3.1 Parameter checking 64
- Simple mode parameter 65
- 3.3.2 Main parameter settings 66
- 3.4 Operation 68
- CONTROL PANEL 69
- 3.4.3 PU operation mode 70
- 3.4.4 Combined operation mode 71
- CHAPTER 4 72
- PARAMETERS 72
- 4 PARAMETERS 73
- 4.1 Parameter List 73
- Output frequency (Hz) 81
- Output voltage 81
- (Pr. 52 to Pr. 54, Pr. 158) 99
- With alarm 100
- PARAMETERS 101
- 4.2.29 Applied motor (Pr. 71) 110
- 4.2.31 Voltage input (Pr. 73) 112
- (Pr. 75) 113
- Time (Minute) 131
- Minute (Second) 131
- (Pr. 135 to Pr. 139) 140
- Set time (s) 149
- Overload status (OL output) 149
- OL output signal 149
- (Pr. 170, Pr. 171) 151
- Pr. 516 Pr. 504 163
- Pr. 502 + Pr. 503 163
- (Pr. 902 to Pr. 905) 170
- MON EXT PU 172
- PROTECTIVE FUNCTIONS 176
- 5 PROTECTIVE FUNCTIONS 177
- 5.1 Errors (Alarms) 177
- (2) Minor fault 184
- (3) Warnings 184
- 5.1.4 Alarm code output 187
- 5.1.5 Resetting the inverter 187
- 5.2 Troubleshooting 188
- 5.3.2 Check items 190
- 5.3.3 Periodic inspection 190
- 5.3.5 Pressure test 191
- <Preparation> 193
- <Checking method> 193
- Fan cover 194
- Fan connectors 194
- <Example: FR-F540-5.5K> 194
- 5.3.8 Inverter replacement 195
- CHAPTER 6 198
- SPECIFICATIONS 198
- 6 SPECIFICATIONS 199
- 6.1 Standard Specifications 199
- 6.1.2 Common specifications 201
- 95 (3.74) 203
- CHAPTER 7 207
- 7 OPTIONS 208
- 7.1 Option List 208
- • Inboard options 210
- APPENDICES 211
- Appendix 1 Data Code List 212
- REVISIONS 217
Related products and manuals for Power adapters & inverters Mitsubishi Electric FR-E540
(57 pages)© 2020, manymanuals.com. All rights reserved. | 0.124 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals