Mitsubishi Electric FR-E540 Instruction Manual Page 179
- Page / 217
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
PROTECTIVE FUNCTIONS
165
Operation Panel
Indication
E.THM
FR-PU04
Motor Overload
Name
Motor overload shut-off (electronic overcurrent protection) (Note 1)
Description
The electronic overcurrent protection in the inverter detects motor overheat due
to overload or reduced cooling capability during constant-speed operation.
When 85% of the preset value is reached, pre-alarm (TH indication) occurs.
When the specified value is reached, the protective circuit is activated to stop
the inverter output. When a special motor such as a multi-pole motor or two or
more motors are run, provide a thermal relay in the inverter output side since
the motor(s) cannot be protected by the electronic overcurrent protection.
Check point
Check the motor for use under overload.
Corrective action
•
Reduce the load weight.
•
For a constant-torque motor, change the Pr. 71 setting to the constant-torque
motor setting.
Operation Panel
Indication
E.THT
FR-PU04
Inv. Overload
Name
Inverter overload shut-off (electronic overcurrent protection) (Note 1)
Description
If a current of more than 120% of the rated output current flows and overcurrent
shut-off does not occur (150% or less), inverse-time characteristics cause the
electronic overcurrent protection to be activated to stop the inverter output in
order to protect the output transistors.
(Overload immunity 120%, 60s.)
Check point
Check the motor for use under overload.
Corrective action
Reduce the load weight.
Note 1: Resetting the inverter initializes the internal heat integrating data of the electronic overcurrent
protection.
Operation Panel
Indication
E.IPF
FR-PU04
Inst. Pwr. Loss
Name
Instantaneous power failure protection
Description
If a power failure occurs for longer than 15ms (this also applies to inverter input
shut-off), the instantaneous power failure protective function is activated to stop
the inverter output in order to prevent the control circuit from malfunctioning. At
this time, the alarm warning output contacts open (across terminals B-C) and
close (across terminals A-C). (Note 2) If a power failure persists for longer than
100ms, the alarm warning output is not provided, and the inverter restarts if the
start signal is on upon power restoration. (The inverter continues operating if an
instantaneous power failure is within 15ms.)
Check point
Find the cause of instantaneous power failure occurrence.
Corrective action
•
Remedy the instantaneous power failure.
•
Prepare a backup power supply for instantaneous power failure.
•
Set the function of automatic restart after instantaneous power failure. (Refer
to page 89.)
Note 2: When an instantaneous power failure occurs, the alarm display and alarm output are not provided,
but the inverter performs protective operation to prevent a fault from occurring in itself. In some
operating status (load size, acceleration/deceleration time setting, etc.), overcurrent or other
protection may be activated upon power restoration.
- FR-F520-0.75K to 55K 1
- FR-F540-0.75K to 55K(-EC) 1
- FR-F520-11K to 55K-NA 1
- FR-F540-11K to 55K-NA 1
- SAFETY INSTRUCTIONS 3
- 1. Electric Shock Prevention 3
- 2. Fire Prevention 3
- 3. Injury Prevention 3
- 4. Additional instructions 4
- (2) Wiring 4
- (3) Trial run 4
- (4) Operation 4
- (5) Emergency stop 5
- (7) Disposing of the inverter 5
- (8) General instructions 5
- CONTENTS 6
- Contents 6
- 6 SPECIFICATIONS 184 9
- 7 OPTIONS 192 9
- APPENDICES 195 9
- CHAPTER 1 10
- 1.1 Pre-Operation Information 11
- 1.2 Basic Configuration 12
- 1.3 Structure 13
- Front cover 14
- Inverter 14
- INSTALLATION AND WIRING 17
- 2.1 Installation 18
- 2.2 Wiring 20
- Notes on Grounding 24
- EC version 30
- NA and Japanese version 30
- Twin contact 38
- Low-level signal contacts 38
- 2.3 Other wiring 39
- 2.3.6 Peripheral devices 48
- 2.3.9 Earthing (EC version) 53
- CHAPTER 3 54
- OPERATION/CONTROL 54
- 3.1 Pre-Operation Information 55
- 3.1.2 Power on 57
- 3.2 Operation Panel 58
- 3.2.3 Monitoring 59
- 3.2.4 Frequency setting 59
- 3.2.6 Operation mode 61
- 3.2.7 Help mode 61
- 3.2.8 Copy mode 63
- 3.3.1 Parameter checking 64
- Simple mode parameter 65
- 3.3.2 Main parameter settings 66
- 3.4 Operation 68
- CONTROL PANEL 69
- 3.4.3 PU operation mode 70
- 3.4.4 Combined operation mode 71
- CHAPTER 4 72
- PARAMETERS 72
- 4 PARAMETERS 73
- 4.1 Parameter List 73
- Output frequency (Hz) 81
- Output voltage 81
- (Pr. 52 to Pr. 54, Pr. 158) 99
- With alarm 100
- PARAMETERS 101
- 4.2.29 Applied motor (Pr. 71) 110
- 4.2.31 Voltage input (Pr. 73) 112
- (Pr. 75) 113
- Time (Minute) 131
- Minute (Second) 131
- (Pr. 135 to Pr. 139) 140
- Set time (s) 149
- Overload status (OL output) 149
- OL output signal 149
- (Pr. 170, Pr. 171) 151
- Pr. 516 Pr. 504 163
- Pr. 502 + Pr. 503 163
- (Pr. 902 to Pr. 905) 170
- MON EXT PU 172
- PROTECTIVE FUNCTIONS 176
- 5 PROTECTIVE FUNCTIONS 177
- 5.1 Errors (Alarms) 177
- (2) Minor fault 184
- (3) Warnings 184
- 5.1.4 Alarm code output 187
- 5.1.5 Resetting the inverter 187
- 5.2 Troubleshooting 188
- 5.3.2 Check items 190
- 5.3.3 Periodic inspection 190
- 5.3.5 Pressure test 191
- <Preparation> 193
- <Checking method> 193
- Fan cover 194
- Fan connectors 194
- <Example: FR-F540-5.5K> 194
- 5.3.8 Inverter replacement 195
- CHAPTER 6 198
- SPECIFICATIONS 198
- 6 SPECIFICATIONS 199
- 6.1 Standard Specifications 199
- 6.1.2 Common specifications 201
- 95 (3.74) 203
- CHAPTER 7 207
- 7 OPTIONS 208
- 7.1 Option List 208
- • Inboard options 210
- APPENDICES 211
- Appendix 1 Data Code List 212
- REVISIONS 217
Related products and manuals for Power adapters & inverters Mitsubishi Electric FR-E540
(57 pages)© 2020, manymanuals.com. All rights reserved. | 0.405 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals