Mitsubishi Electric UD8400U-W User Manual Page 49
- Page / 76
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
EN-49
Initial network settings
You can set the network of the projector using the
menu.
NETWORK CONTROLLER
NETWORK PASSWORD
NETWORK
1
1
2
2
NETWORK CERTIFICATION
PROJECTOR NAME
IP CONFIG
NETWORK RESET
opt.
STANDARD
ENTER
ENTER
OK
ON
Setting Projector Name
(See page 32 for menu setting.)
1. Display the NETWORK menu.
2. Press the S or T button to select PROJECTOR
NAME.
PROJECTOR NAME
SET
3. Press the W or X button to select SET .
4. Press the ENTER button.
• PROJECTOR NAME screen appears.
PROJECTOR NAME
CODE : XXXXX V Z $ %
A
OK
caps
NEXT
SPACE
CLEAR
DEL
CANCEL
B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
0 1 2 3 4 5 6 7 8 9 – . _
! ” # $ % ’ ( )
*
+ , /
← →
5. Press the direction buttons to move the key cursor,
select the characters or marks to enter, and press
the ENTER button.
• Projector Name can be set using up to 15
characters including alphabets (capital/small),
numeric characters, or marks.
key: ............. Shifting the position of enter
cursor to the left for each
character.
key: ............. Shifting the position of enter
cursor to the right for each
character.
DEL key: .......... Deleting the character in the
position of enter cursor for each
character.
caps/CAPS key:
Switching an alphabet character
to CAPITAL or small.
NEXT/PREV key:
Switching the marks listed on
the fourth line.
SPACE key: ..... Inserting a space in the position
of enter cursor.
CLEAR key: ..... Deleting all the entered
characters.
• You can enter numbers by pressing the number
buttons (0 to 9) while holding down the NUM
button on the remote control.
6. When selecting OK, the setting is completed as the
name stored. However, when selecting CANCEL,
the setting is completed without storing.
• The display returns the NETWORK menu after
selecting OK or CANCEL.
• It may take some time to refl ect the settings.
Network Password Settings
(See page 32 for menu setting.)
1. Display the NETWORK menu.
2. Press the S or Tbutton to select NETWORK
PASSWORD.
NETWORK PASSWORD
ENTER
3. Press the ENTER button.
• CURRENT NETWORK PASSWORD screen
appears.
CURRENT NETWORK PASSWORD
A
OK
caps
CLEAR
DEL
CANCEL
B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
0 1 2 3 4 5 6 7 8 9
← →
∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
4. Press the direction buttons to move the key cursor,
select the characters or marks to enter, and press
the ENTER button.
• Password can be set using up to 32 characters
including alphabets (capital/small) or numeric
characters.
key: ............. Shifting the position of enter
cursor to the left for each
character.
key: ............. Shifting the position of enter
cursor to the right for each
character.
DEL key: .......... Deleting the character in the
position of enter cursor for each
character.
caps/CAPS key:
Switching an alphabet character
to CAPITAL or small.
CLEAR key: ..... Deleting all the entered
characters.
• You can enter numbers by pressing the number
buttons (0 to 9) while holding down the NUM
button on the remote control.
• The default password is “admin”.
5. Select OK, and NEW NETWORK PASSWORD
screen appears if the entered password is correct.
• If the entered password is not correct,
CURRENT NETWORK PASSWORD screen
appears again.
CONFIRM NETWORK PASSWORD
A
OK
caps
CLEAR
DEL
CANCEL
B C D E F G H I J K L M
N O P Q R S T U V W X Y Z
0 1 2 3 4 5 6 7 8 9
← →
↔
∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
NEW NETWORK PASSWORD
∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
- User Manual 1
- WARNING: 2
- CAUTION: 2
- Contents 3
- Important safeguards 4
- Preparing your projector 6
- Overview 7
- Bottom side 8
- Remote control 8
- Using the remote control 9
- Important: 10
- Setting up your projector 11
- Setup adjustment 12
- Setting the projector posture 13
- KEYSTONE 14
- SELECT : BLANK 14
- RESET KEYSTONE 14
- RESET LOWER RIGHT 15
- LOWER RIGHT 15
- Rear projection 18
- Viewing computer images 19
- B. Plugging the power cord 20
- VIDEO IN S-VIDEO IN IN-1 21
- D. Projecting images 22
- To stop projecting: 23
- Direct Power OFF 23
- AUTO POSITION button 24
- Setting of the resolution 24
- Setting the aspect ratio 25
- Viewing video images 26
- Equipment having an 27
- HDMI terminal 27
- To HDMI terminal 27
- B. Plugging in the power cord 28
- Menu operation 31
- Menu operation (continued) 32
- Adjusting projected images 42
- Color Enhancer 43
- SUPER RESOLUTION 44
- NCM−USER 44
- - USER menu 46
- Correction position marker 47
- Resetting the settings 48
- Initial network settings 49
- IP Settings 50
- Setting the control system 51
- NETWORK RESET 52
- Lamp relay 53
- Illuminating 54
- Advanced features 55
- Advanced features (continued) 56
- PROJECTOR ID 60
- GROUP ID 60
- COMPUTER1 61
- COMPUTER2 61
- VIDEO S-VIDEO 61
- Replacing the lamp 62
- EXECUTE LAMP 1 TIME RESET ? 63
- OK : ENTER CANCEL : MENU 63
- Maintenance 64
- Automatic cleaning fi lter 65
- Dust check window 66
- Troubleshooting 67
- Troubleshooting (continued) 68
- Indicators 71
- Specifi cations 72
- Specifi cations (continued) 73
- ITSUBISHI 76
- ELECTRIC CORPORATIO 76
Related products and manuals for Data projectors Mitsubishi Electric UD8400U-W
(39 pages)© 2020, manymanuals.com. All rights reserved. | 1.896 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals