Mitsubishi Electric UD8400U-W User Manual Page 72
- Page / 76
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
EN-72
Specifi cations
The specifi cations and outside appearance of the projector are subject to change without prior notice.
Type DLP™ projector
Model UD8400U
Display technology 0.67-inch Single chip DMD
Pixel 1920 x 1200 = 2304000 pixels
Projection lens F 2.0 - 2.4 f= 24.5 - 33.1 mm
Light-source lamp 330 W x 2
Image size (projection distance) 40” min. to 300” max. (projection distance 1.4 to 10.9 m)
Maximum resolution Computer signal Maximum resolution: 1920 x 1200 dots
Panel resolution: 1920 x 1200 dots
Video signal NTSC/PAL/SECAM/4.43NTSC/PAL-M/PAL-N/PAL-60
Component signal 480i, 480p, 576i, 576p, 720p, 1080i, 1080p
Panel resolution: 1920 x 1200 dots
Computer/component video input [Signal type] [Terminal type] [Line]
Analog RGB Mini D-SUB 15-pin 1
Analog RGB 5 BNC 1
Digital RGB DVI-D 24-pin 1
Video input [Signal type] [Terminal type] [Line]
Video input BNC 1
S-video input S 1
HDMI input [Signal type] [Terminal type] [Line]
HDMI HDMI 19-pin 1
SDI input [Signal type] [Terminal type] [Line]
SDI BNC 1
Control terminal/others SERIAL IN/OUT (D-SUB 9-pin male) RS-232C standards,
LAN (RJ-45), REMOTE 1 IN (D-SUB 9-pin female), REMOTE2 IN/OUT
(Stereo mini jack (ø3.5))
Operating temperatures +41°F (+5°C) to +104°F (+40°C): ( Standard altitude mode: Floor
installation/ceiling installation)
+41°F (+5°C) to +95°F (+35°C): (Other than above.)
Rated voltage AC 100 - 240 V, 50/60 Hz
Power consumption 8.7 A, 870 W
During standby:
AC 100 - 120 V: 2 W (when STANDBY MODE is STANDARD)
0.2 W (when STANDBY MODE is LOW)
AC 220 - 240 V: 2 W (when STANDBY MODE is STANDARD)
0.3 W (when STANDBY MODE is LOW)
Dimensions (not including protrusion)
490 mm (W) x 201 mm (H) x 421 mm (D) (projector only)
490 mm (W) x 201 mm (H) x 506 mm (D) (including the terminal cover)
Weight 16 kg (projector only), 16.5 kg (including the terminal cover)
Others S-video input Luminance signal: Vp-p=1.0 V 75 Ω (negative sync)
Chrominance signals: Vp-p=0.286 V 75 Ω (burst signal)
Video input Vp-p=1.0 V 75 Ω (negative sync)
Component video
input
YC
B
C
R
: Vp-p=1.0 V 75 Ω (Y) (negative sync)
Vp-p=0.7 V 75 Ω (C
B
, C
R
)
Analog input RGB: Vp-p=0.7 V 75 Ω (negative sync)
YC
B
C
R
: Vp-p=1.0 V (Y) (negative sync) Vp-p=0.7 V (C
B
, C
R
)
HD/CS: TTL-level (negative or positive polarity)
VD: TTL-level (negative or positive polarity)
Digital input (DVI) DVI-D interface (TMDS single link) with HDCP
Digital input (HDMI) HDMI interface (TMDS single link)
Digital input (SDI) SDI interface:
SD-SDI (YC
B
C
R
4:2:2 10 bits)
HD-SDI (YP
B
P
R
4:2:2 10 bits)
3G-SDI (YP
B
P
R
4:2:2 10 bits)
Replacement part (option/not included in the box)
Spare lamp: VLT-XD8000LP
Option lenses: OL-XD2000SZ, OL-XD2000LZ, OL-XD2000TZ, OL-XD8000UZ, OL-XD2000FR
Option color-wheel: CW-FC2
Important:
• Ask a trained specialist for mounting or replacing the option lens or the option color-wheel. For details, contact
your dealer.
- User Manual 1
- WARNING: 2
- CAUTION: 2
- Contents 3
- Important safeguards 4
- Preparing your projector 6
- Overview 7
- Bottom side 8
- Remote control 8
- Using the remote control 9
- Important: 10
- Setting up your projector 11
- Setup adjustment 12
- Setting the projector posture 13
- KEYSTONE 14
- SELECT : BLANK 14
- RESET KEYSTONE 14
- RESET LOWER RIGHT 15
- LOWER RIGHT 15
- Rear projection 18
- Viewing computer images 19
- B. Plugging the power cord 20
- VIDEO IN S-VIDEO IN IN-1 21
- D. Projecting images 22
- To stop projecting: 23
- Direct Power OFF 23
- AUTO POSITION button 24
- Setting of the resolution 24
- Setting the aspect ratio 25
- Viewing video images 26
- Equipment having an 27
- HDMI terminal 27
- To HDMI terminal 27
- B. Plugging in the power cord 28
- Menu operation 31
- Menu operation (continued) 32
- Adjusting projected images 42
- Color Enhancer 43
- SUPER RESOLUTION 44
- NCM−USER 44
- - USER menu 46
- Correction position marker 47
- Resetting the settings 48
- Initial network settings 49
- IP Settings 50
- Setting the control system 51
- NETWORK RESET 52
- Lamp relay 53
- Illuminating 54
- Advanced features 55
- Advanced features (continued) 56
- PROJECTOR ID 60
- GROUP ID 60
- COMPUTER1 61
- COMPUTER2 61
- VIDEO S-VIDEO 61
- Replacing the lamp 62
- EXECUTE LAMP 1 TIME RESET ? 63
- OK : ENTER CANCEL : MENU 63
- Maintenance 64
- Automatic cleaning fi lter 65
- Dust check window 66
- Troubleshooting 67
- Troubleshooting (continued) 68
- Indicators 71
- Specifi cations 72
- Specifi cations (continued) 73
- ITSUBISHI 76
- ELECTRIC CORPORATIO 76
Related products and manuals for Data projectors Mitsubishi Electric UD8400U-W
(39 pages)© 2020, manymanuals.com. All rights reserved. | 2.374 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals