Mitsubishi Electric FR-E540 Instruction Manual Page 18
- Page / 217
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
2.1 Installation
INSTALLATION AND WIRING
7
2 INSTALLATION AND WIRING
2.1 Installation
2.1.1 Instructions for installation
1) Handle the unit carefully.
The inverter uses plastic parts. Handle it gently to protect it from damage. Also, hold the unit with even
strength and do not apply too much strength to the front cover alone.
2) Install the inverter in a place where it is immune to vibration. (5.9 m/s
2
or less)
Also note the cart, press, etc.
3) Note on ambient temperature
The inverter life is under great influence of ambient temperature. In the place of installation, ambient
temperature must be within the permissible range (depending upon the operation mode and conditions
(see ambient temperature specifications on page 187). Check that the ambient temperature is within that
range in the positions shown in figure 3)).
4) Install the inverter on a non-combustible surface.
The inverter will be very hot (maximum about 150
°
C (302
°
F)). Install it on a non-combustible surface (e.g.
metal). Also leave sufficient clearances around the inverter.
5) Avoid high temperature and high humidity.
Avoid direct sunlight and places of high temperature and high humidity.
6) The amount of heat generated in an enclosure can be reduced considerably by placing the heat sink
outside the enclosure.
Note: 1. Use the option (FR-A5CN
""
) for installation. The mounting area should be cut to the panel
cutting dimensions.
2. The cooling section outside the enclosure has the cooling fan. Do not use the inverter in any
environment where it is exposed to waterdrops, oil mist, dust, etc.
7) Avoid places where the inverter is exposed to oil mist, flammable gases, fluff, dust, dirt etc.
Install the inverter in a clean place or inside a "totally enclosed" panel, which does not accept any
suspended matter.
8) Note the cooling method when the inverter is installed in an enclosure.
When two or more inverters are installed or a ventilation fan is mounted in an enclosure, the inverters and
ventilation fan must be installed in proper positions with extreme care taken to keep the ambient
temperatures of the inverters below the permissible value. If they are installed in improper positions, the
ambient temperatures of the inverters will rise and ventilation effect will be reduced.
9) Install the inverter securely in the vertical direction with screws or bolts.
3) Note on ambient temperature
Measurement
position
Measurement
position
5cm5cm
5cm
(1.97inches)
(1.97inches)
(1.97inches)
4) Clearances around the inverter
*: 1cm (0.39inches) or more for model 3.7K or less
These clearances are also necessary for changing the cooling fan.
Leave sufficient
clearances above
and under the
inverter to ensure
adequate ventilation.
Cooling fan
built
in the inverter
Cooling
air
10cm (3.94inches) or
5cm (1.97inches) or more *
5cm (1.97inches) or more *
more
10cm (3.94inches) or
more
- FR-F520-0.75K to 55K 1
- FR-F540-0.75K to 55K(-EC) 1
- FR-F520-11K to 55K-NA 1
- FR-F540-11K to 55K-NA 1
- SAFETY INSTRUCTIONS 3
- 1. Electric Shock Prevention 3
- 2. Fire Prevention 3
- 3. Injury Prevention 3
- 4. Additional instructions 4
- (2) Wiring 4
- (3) Trial run 4
- (4) Operation 4
- (5) Emergency stop 5
- (7) Disposing of the inverter 5
- (8) General instructions 5
- CONTENTS 6
- Contents 6
- 6 SPECIFICATIONS 184 9
- 7 OPTIONS 192 9
- APPENDICES 195 9
- CHAPTER 1 10
- 1.1 Pre-Operation Information 11
- 1.2 Basic Configuration 12
- 1.3 Structure 13
- Front cover 14
- Inverter 14
- INSTALLATION AND WIRING 17
- 2.1 Installation 18
- 2.2 Wiring 20
- Notes on Grounding 24
- EC version 30
- NA and Japanese version 30
- Twin contact 38
- Low-level signal contacts 38
- 2.3 Other wiring 39
- 2.3.6 Peripheral devices 48
- 2.3.9 Earthing (EC version) 53
- CHAPTER 3 54
- OPERATION/CONTROL 54
- 3.1 Pre-Operation Information 55
- 3.1.2 Power on 57
- 3.2 Operation Panel 58
- 3.2.3 Monitoring 59
- 3.2.4 Frequency setting 59
- 3.2.6 Operation mode 61
- 3.2.7 Help mode 61
- 3.2.8 Copy mode 63
- 3.3.1 Parameter checking 64
- Simple mode parameter 65
- 3.3.2 Main parameter settings 66
- 3.4 Operation 68
- CONTROL PANEL 69
- 3.4.3 PU operation mode 70
- 3.4.4 Combined operation mode 71
- CHAPTER 4 72
- PARAMETERS 72
- 4 PARAMETERS 73
- 4.1 Parameter List 73
- Output frequency (Hz) 81
- Output voltage 81
- (Pr. 52 to Pr. 54, Pr. 158) 99
- With alarm 100
- PARAMETERS 101
- 4.2.29 Applied motor (Pr. 71) 110
- 4.2.31 Voltage input (Pr. 73) 112
- (Pr. 75) 113
- Time (Minute) 131
- Minute (Second) 131
- (Pr. 135 to Pr. 139) 140
- Set time (s) 149
- Overload status (OL output) 149
- OL output signal 149
- (Pr. 170, Pr. 171) 151
- Pr. 516 Pr. 504 163
- Pr. 502 + Pr. 503 163
- (Pr. 902 to Pr. 905) 170
- MON EXT PU 172
- PROTECTIVE FUNCTIONS 176
- 5 PROTECTIVE FUNCTIONS 177
- 5.1 Errors (Alarms) 177
- (2) Minor fault 184
- (3) Warnings 184
- 5.1.4 Alarm code output 187
- 5.1.5 Resetting the inverter 187
- 5.2 Troubleshooting 188
- 5.3.2 Check items 190
- 5.3.3 Periodic inspection 190
- 5.3.5 Pressure test 191
- <Preparation> 193
- <Checking method> 193
- Fan cover 194
- Fan connectors 194
- <Example: FR-F540-5.5K> 194
- 5.3.8 Inverter replacement 195
- CHAPTER 6 198
- SPECIFICATIONS 198
- 6 SPECIFICATIONS 199
- 6.1 Standard Specifications 199
- 6.1.2 Common specifications 201
- 95 (3.74) 203
- CHAPTER 7 207
- 7 OPTIONS 208
- 7.1 Option List 208
- • Inboard options 210
- APPENDICES 211
- Appendix 1 Data Code List 212
- REVISIONS 217
Related products and manuals for Power adapters & inverters Mitsubishi Electric FR-E540
(57 pages)© 2020, manymanuals.com. All rights reserved. | 2.089 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals