Mitsubishi Electric F700 Instruction Manual Page 24
- Page / 143
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
19
Wiring
2
INSTALLATION AND WIRING
*1 Low indicates that the open collector output transistor is on (conducts).
High indicates that the transistor is off (does not conduct).
*2 Not output during inverter reset.
(3) Communication
(4) Control circuit terminal layout
(5) Wiring instructions
1) Terminals 5, SD and SE are common to the I/O signals and isolated from each other. Do not earth (Ground).
Avoid connecting the terminal SD and 5 and the terminal SE and 5.
2) Use shielded or twisted cables for connection to the control circuit terminals and run them away from the main
and power circuits (including the 200V relay sequence circuit).
3) Use two or more parallel micro-signal contacts or twin
contacts to prevent a contact faults when using contact inputs
since the control circuit input signals are micro-currents.
4) Do not apply a voltage to the contact input terminals (e.g. STF) of the control circuit.
5) Always apply a voltage to the alarm output terminals (A, B, C) via a relay coil, lamp, etc.
6) It is recommended to use the cables of 0.75mm
2
gauge for connection to the control circuit terminals.
If the cable gauge used is 1.25mm
2
or more, the front cover may be lifted when there are many cables running
or the cables are run improperly, resulting in an operation panel contact fault.
7) The wiring length should be 30m maximum.
Pulse
FM For meter
Select one e.g. output frequency
from monitor items.
*2
The output signal is proportional to
the magnitude of the corresponding
monitoring item.
Output item:
Output frequency
(initial setting)
Permissible load
current 2mA
1440 pulses/s at
60Hz
Instruction
Manual
(applied)
Analog
AM
Analog signal
output
Output item:
Output frequency
(initial setting)
Output signal 0
to 10VDC
Permissible load
current 1mA
(load impedance
10kΩ or more)
Resolution 8 bit
Instruction
Manual
(applied)
Type
Terminal
Symbol
Terminal
Name
Description Refer to
RS-485
—
PU
connector
With the PU connector, communication can be made through RS-485.
(for connection on a 1:1 basis only)
. Conforming standard : EIA-485(RS-485)
. Transmission format : Multidrop
. Communication speed : 4800 to 38400bps
. Overall length : 500m
24
RS-485 terminals
TXD+
Inverter
transmission
terminal
With the RS-485 terminals, communication can be made through RS-485.
Conforming standard : EIA-485(RS-485)
Transmission format : Multidrop link
Communication speed : 300 to 38400bps
Overall length : 500m
25
TXD-
RXD+
Inverter
reception
terminal
RXD-
SG
Earth
(Ground)
Terminal screw size: M3.5
Tightening torque: 1.2N·m
Type
Terminal
Symbol
Terminal
Name
Description
Rated
Specifications
Refer to
A1 B1 C1 A2 B2 C2 10E 10 2 5 4
1AMSDRES
MRS
STOP
AURTRHRMRL
PCCSJOGSTRSTFSDSDFUOLIPFSURUNSE
FM
Micro signal contacts Twin contacts
- INSTRUCTION MANUAL (BASIC) 1
- INVERTER 1
- 4. Additional Instructions 2
- Environment 2
- , surge suppressor or radio 2
- 2 INSTALLATION AND WIRING 2 3
- 3 DRIVE THE MOTOR 28 3
- 4 ADJUSTMENT 51 4
- 5 TROUBLESHOOTING 62 4
- 7 SPECIFICATIONS 91 5
- APPENDICES 110 5
- FR --F740 6
- 2 INSTALLATION AND WIRING 7
- 2.1 Peripheral devices 8
- Peripheral devices 9
- INSTALLATION AND WIRING 10
- •Reinstallation 11
- 2.4 Wiring 13
- 200V class 14
- Screw size 17
- Cable Sizes 19
- (3) Total wiring length 21
- (2) Output signals 23
- (separate power) 25
- (7) Control logic switchover 27
- 2.4.7 RS-485 terminal block 30
- 2.4.8 Communication operation 30
- 3.1 Step of operation 33
- 3.2 Operation panel (FR-DU07) 34
- Operation panel (FR-DU07) 35
- DRIVE THE MOTOR 36
- Operation 37
- 3 Base frequency 39
- (PU operation mode) 40
- Flickering 42
- Operation Display 43
- DisplayOperation 45
- 11. Stop 45
- (external operation) 48
- Three-phase 50
- AC power supply 50
- 10. Stop 51
- 7. Mode/monitor check 51
- 4 ADJUSTMENT 56
- CAUTION 58
- (Pr.7, Pr.8) 59
- ADJUSTMENT 60
- 4.7 Parameter clear 63
- 4.8 All parameter clear 64
- 4.9 Parameter copy 65
- 4.10 Parameter verification 66
- 5.1 List of alarm display 67
- Causes and corrective actions 68
- TROUBLESHOOTING 68
- Inverter 79
- (2) Clearing procedure 81
- 6.1 Inspection Item 84
- Inspection Item 85
- 6.1.6 Cleaning 88
- 6.1.7 Replacement of parts 89
- 6.1.8 Inverter replacement 93
- Earth (ground) terminal 94
- Measuring 95
- 7.1 Rating 96
- •400V class 97
- 7.2 Common specifications 98
- Common specifications 99
- Outline dimension drawings 100
- SPECIFICATIONS 100
- • DC reactor supplied 106
- • FR-F740-250K, 280K, 315K 106
- • FR-F740-400K 108
- • FR-F740-450K 109
- • FR-F740-500K, 560K 110
- • FR-PU04 111
- • FR-F740-185K to 315K 113
- • FR-F740-355K or more 113
- APPENDICES 115
- Extended parameters 117
- Extended parameter list 118
- (2) Wiring instructions 139
- Instructions for installation 140
- (1) EMC Directive 142
- (2) Low Voltage Directive 142
- Print Date 143
- Manual Number 143
- Revision 143
Related products and manuals for Power adapters & inverters Mitsubishi Electric F700
(59 pages)© 2020, manymanuals.com. All rights reserved. | 0.456 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals