Mitsubishi Electric Q172CPU User Manual Page 154
- Page / 234
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
4 - 15
4 INSTALLATION AND WIRING
4.5 Wiring
4.5.1 Instructions for wiring
!
DANGER
Completely turn off the all lines of the power supply externally before wiring. Not completely turning off
all power could result in electric shock or damage to the product.
When turning on the power supply or operating the module after wiring, be sure that the module's
terminal covers are correctly attached. Not attaching the terminal cover could result in electric
shock.
!
CAUTION
Be sure to ground of the earth terminal FG and LG. Not doing so could result in electric shock or
operation failure. (Ground resistance: 100
or less)
When wiring in the Motion controller, be sure that it is done correctly by checking the product's rated
voltage and the terminal layout. Connecting a power supply that is different from the rating or
incorrectly wiring the product could result in fire or damage.
External connections shall be crimped or pressure welded with the specified tools, or correctly
soldered. Imperfect connections could result in short circuit, fire, or operation failure.
Tighten the terminal screws within the specified torque range. If the terminal screws are loose, it could result in
short circuit, fire, or operation failure. Tightening the terminal screws too far may cause damages to the screws
and/or the module, resulting in drop, short circuit, or operation failure.
Be sure there are no foreign matters such as sawdust or wiring debris inside the module. Such debris
could cause fire, damage, or operation
failure.
The module has an ingress prevention label on its top to prevent foreign matter, such as wiring
debris, from entering the module during wiring.
Do not remove this label during wiring.
Before starting system operation, be sure to remove this label because of heat dissipation.
This section described instructions for the wiring of the power supply.
(1) Power supply wiring
(a) 100VAC, 200VAC and 24VDC wires should be twisted as dense as possible
respectively. Connect the modules with the shortest distance.
Also, to reduce the voltage drop to the minimum, use the thickest wires
possible.
Use the wires of the following core size for wiring.
Application Recommended core size
100VAC, 200VAC, 24VDC wires 2.0mm
2
or less
I/O equipment 0.75mm
2
(0.75 to 1.5mm
2
usable)
Ground wire 2.0mm
2
or more
- MOTION CONTROLLERS 1
- SAFETY PRECAUTIONS 2
- (1) System structure 4
- CAUTION 10
- 1. OVERVIEW 18
- (Note-2) : SSCNET: S 19
- 2. SYSTEM CONFIGURATION 20
- SSCNET cable 21
- (a) MR-H BN 39
- (c) FR-V5 0 41
- (4) Software packages 41
- (a) PLC software package 42
- 2.3 General Specifications 43
- (2) Q173CPU/Q172CPU 46
- Q172CPU(N) 48
- (a) Module specifications 49
- 2.4.2 Power supply module 55
- 100-120VAC 58
- (When using the Q173CPUN-T.) 61
- (4) I/O allocations 64
- (1) Q172LX name of parts 65
- (b) Input 66
- (a) Servo external signals 67
- • Tracking enable signal 73
- Q173CPU(N)/ 74
- Cable length 10m (32.81ft.) 76
- (b) Q172EX-S2/Q172EX-S3 77
- (a) Specifications 78
- Battery Specifications 78
- (b) Battery replacement 78
- Q173PX-S1 80
- (Note-1)(Note-2) 81
- (Duty ratio: 50% 25%) 86
- 20 s or more 86
- A4 A3 A2 87
- B4 B3 B2 87
- CN1A CN1B 101
- 2 SYSTEM CONFIGURATION 102
- (h) FR-V5NSCBL 107
- (a) MR-H-BN configuration 108
- (b) MR-J2 -B configuration 108
- 1) Example of Q173CPU(N) 110
- 2) Example of Q172CPU(N) 112
- 2.4.10 External battery 115
- 3. DESIGN 120
- 3 DESIGN 123
- 3.2 External Circuit Design 123
- MR-J2-03B5 124
- Electro 124
- (For A31TU-DN ) 125
- (For A31TU-D3 ) 127
- MC1 N0 M10 129
- (2) Grounding 131
- Forced stop 132
- Internal 132
- Wpw= (I 136
- 3.4 Design Checklist 139
- 4 INSTALLATION AND WIRING 141
- (1) Fitting dimensions 142
- Vertical Flat 143
- Motion CPU 146
- PC connector 147
- Battery cable 148
- CPU/BAT connecto 148
- Battery unit 148
- (Q170BAT) 148
- TU connector 149
- (3) Grounding 156
- [Servo data setting 162
- Power supply module 171
- PLC CPU module 171
- Motion CPU module 171
- I/O module 172
- 6.3 Periodic Inspection 173
- 6.4 External Battery 174
- (Note-1) 175
- (Note-3) 175
- (Note-2) 175
- MITSUBISHI 176
- LITHIUM BATTERY 176
- Lithium battery 178
- Memory card socket 178
- Is the power 182
- 132VAC or 170 to 264VAC? 182
- "RUN" LED 184
- For the case of 1) 184
- For the case of 2) 184
- When started the latch clear 186
- Are the output 188
- USB driver installed 190
- Win 98/2000/XP? 190
- DC input 192
- (plus common) 192
- Input module 192
- Resistor 192
- Output module 194
- APPENDICES 196
- PPENDICES 198
- (a) Q172J2BCBL M(-B) 198
- 1) Model explanation 198
- 2) Connection diagram 198
- (b) Q172HBCBL M(-B) 199
- Q173DVCBL M 200
- (d) Q173J2B CBL M 201
- (e) Q173HB CBL M 202
- :Twisted pair cable 203
- (h) MR-HBUS M 205
- (2) MR-JHSCBL M-L/H 207
- (a) Model explanation 207
- (b) Connection diagram 207
- (3) Q170ENCCBL M 208
- (Note) 209
- Q170TUD3CBL3M 211
- Q170TUDNCBL3M 212
- 27.4(1.08) 215
- 98(3.86) 215
- 114.3(4.50) 215
- 46(1.81) 215
- 79.5(3.13) 215
- (3) Q172CPUN-T Module 216
- (4) Q173CPUN-T Module 216
- (5) Q172CPU Module 217
- (6) Q173CPU Module 217
- (1) Q173PX 220
- (2) Q173PX-S1 220
- (2) Q64P 221
- (1) Dividing unit (Q173DV) 222
- (2) Battery unit (Q170BAT) 222
- APPENDIX 2.7 Connector 223
- (6) A31TUD3TM 227
- Effective dimension 229
- Keyway Dimensional Diagram 229
- WARRANTY 233
Related products and manuals for Power adapters & inverters Mitsubishi Electric Q172CPU
(34 pages)© 2020, manymanuals.com. All rights reserved. | 0.279 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals