Mitsubishi Electric Q172CPU User Manual Page 32
- Page / 234
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
2 - 13
2 SYSTEM CONFIGURATION
2.1.4 Restrictions on Motion systems
(1) It is not allowed to use the Motion CPU as the control CPU of a module installed
on the QA1S6
B extension base unit. PLC CPU must be used as the control
CPU.
(2) The connector for installation of memory card on the Motion CPU module is for
future function expansion.
(3) Motion CPU module cannot be used as standalone module. It must always be
used in combination with the PLC CPU module (version that supports Multiple
CPU systems). Moreover, it must be installed on the right side of PLC CPU
module. PLC CPU module cannot be installed in a position to the right of Motion
CPU module.
(4) Personal computer CPU unit must be installed on the right side of Motion CPU
module. Motion CPU module cannot be installed in a position to the right of
personal computer CPU unit.
(5) Make sure to use the PLC CPU module in "Q mode".
(6) Motion CPU module cannot be set as the control CPU of intelligent function
module or Graphic Operation Terminal (GOT).
(7) SSCNET cable which connects the Motion CPU and servo amplifier, and the
teaching unit connecting cable which connects the Motion CPU and A31TU-
D3
/A31TU-DN
(Note-1)
are pulled from the bottom part of unit. Make sure to
secure sufficient space for pulling out the cable when designing the control panel.
(8) Motion CPU module is one module element of Q series multiple PLC system. It
must be set the parameters of Q series multiple PLC system for each PLC CPU.
Motion CPU module must also be set to support the Multiple CPU system in the
system settings.
(9) Make sure to use the Motion CPU as the control CPU of motion modules
dedicated for Motion CPU (Q172LX, Q172EX
(Note-2)
, Q173PX, etc.). They will not
operate correctly if PLC CPU is set and installed as the control CPU by mistake.
Motion CPU is treated as a 32-point intelligent module by PLC CPU of other CPU.
It cannot be accessed from other CPU.
(10) When a Multiple CPU system is configured, make sure to configure the modules
so that the total current consumption of individual modules on the CPU base does
not exceed the 5VDC output capacity of power supply module.
(Refer to Section 2.4.2 (3), (4) "Selection of the power supply module".)
(11) Installation position of the Q172EX-S2/S3
(Note-2)
is only CPU base unit.
(Note-1) : Teaching unit can be used in SV13. It cannot be used in SV22/SV43.
(Note-2) : Q172EX can be used in SV22. It cannot be used in SV13/SV43.
- MOTION CONTROLLERS 1
- SAFETY PRECAUTIONS 2
- (1) System structure 4
- CAUTION 10
- 1. OVERVIEW 18
- (Note-2) : SSCNET: S 19
- 2. SYSTEM CONFIGURATION 20
- SSCNET cable 21
- (a) MR-H BN 39
- (c) FR-V5 0 41
- (4) Software packages 41
- (a) PLC software package 42
- 2.3 General Specifications 43
- (2) Q173CPU/Q172CPU 46
- Q172CPU(N) 48
- (a) Module specifications 49
- 2.4.2 Power supply module 55
- 100-120VAC 58
- (When using the Q173CPUN-T.) 61
- (4) I/O allocations 64
- (1) Q172LX name of parts 65
- (b) Input 66
- (a) Servo external signals 67
- • Tracking enable signal 73
- Q173CPU(N)/ 74
- Cable length 10m (32.81ft.) 76
- (b) Q172EX-S2/Q172EX-S3 77
- (a) Specifications 78
- Battery Specifications 78
- (b) Battery replacement 78
- Q173PX-S1 80
- (Note-1)(Note-2) 81
- (Duty ratio: 50% 25%) 86
- 20 s or more 86
- A4 A3 A2 87
- B4 B3 B2 87
- CN1A CN1B 101
- 2 SYSTEM CONFIGURATION 102
- (h) FR-V5NSCBL 107
- (a) MR-H-BN configuration 108
- (b) MR-J2 -B configuration 108
- 1) Example of Q173CPU(N) 110
- 2) Example of Q172CPU(N) 112
- 2.4.10 External battery 115
- 3. DESIGN 120
- 3 DESIGN 123
- 3.2 External Circuit Design 123
- MR-J2-03B5 124
- Electro 124
- (For A31TU-DN ) 125
- (For A31TU-D3 ) 127
- MC1 N0 M10 129
- (2) Grounding 131
- Forced stop 132
- Internal 132
- Wpw= (I 136
- 3.4 Design Checklist 139
- 4 INSTALLATION AND WIRING 141
- (1) Fitting dimensions 142
- Vertical Flat 143
- Motion CPU 146
- PC connector 147
- Battery cable 148
- CPU/BAT connecto 148
- Battery unit 148
- (Q170BAT) 148
- TU connector 149
- (3) Grounding 156
- [Servo data setting 162
- Power supply module 171
- PLC CPU module 171
- Motion CPU module 171
- I/O module 172
- 6.3 Periodic Inspection 173
- 6.4 External Battery 174
- (Note-1) 175
- (Note-3) 175
- (Note-2) 175
- MITSUBISHI 176
- LITHIUM BATTERY 176
- Lithium battery 178
- Memory card socket 178
- Is the power 182
- 132VAC or 170 to 264VAC? 182
- "RUN" LED 184
- For the case of 1) 184
- For the case of 2) 184
- When started the latch clear 186
- Are the output 188
- USB driver installed 190
- Win 98/2000/XP? 190
- DC input 192
- (plus common) 192
- Input module 192
- Resistor 192
- Output module 194
- APPENDICES 196
- PPENDICES 198
- (a) Q172J2BCBL M(-B) 198
- 1) Model explanation 198
- 2) Connection diagram 198
- (b) Q172HBCBL M(-B) 199
- Q173DVCBL M 200
- (d) Q173J2B CBL M 201
- (e) Q173HB CBL M 202
- :Twisted pair cable 203
- (h) MR-HBUS M 205
- (2) MR-JHSCBL M-L/H 207
- (a) Model explanation 207
- (b) Connection diagram 207
- (3) Q170ENCCBL M 208
- (Note) 209
- Q170TUD3CBL3M 211
- Q170TUDNCBL3M 212
- 27.4(1.08) 215
- 98(3.86) 215
- 114.3(4.50) 215
- 46(1.81) 215
- 79.5(3.13) 215
- (3) Q172CPUN-T Module 216
- (4) Q173CPUN-T Module 216
- (5) Q172CPU Module 217
- (6) Q173CPU Module 217
- (1) Q173PX 220
- (2) Q173PX-S1 220
- (2) Q64P 221
- (1) Dividing unit (Q173DV) 222
- (2) Battery unit (Q170BAT) 222
- APPENDIX 2.7 Connector 223
- (6) A31TUD3TM 227
- Effective dimension 229
- Keyway Dimensional Diagram 229
- WARRANTY 233
Related products and manuals for Power adapters & inverters Mitsubishi Electric Q172CPU
(34 pages)© 2020, manymanuals.com. All rights reserved. | 3.502 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals