Mitsubishi Electric Q172CPU User Manual Page 170
- Page / 234
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
6 - 3
6 INSPECTION AND MAINTENANCE
!
CAUTION
Do not short circuit, charge, overheat, incinerate or disassemble the batteries.
The electrolytic capacitor will generate gas during a fault, so do not place your face near the Motion
controller or servo amplifier.
The electrolytic capacitor and fan will deteriorate. Periodically change these to prevent secondary
damage from faults. Replacements can be made by our sales representative.
If an error occurs in the self diagnosis of the Motion controller or servo amplifier, confirm the check
details according to the instruction manual, and restore the operation.
If a dangerous state is predicted in case of a power failure or product failure, in order to prevent that
state, use a servomotor with electromagnetic brakes for maintenance or install a brake mechanism
externally.
Use a double circuit construction so that the electromagnetic brake operation circuit can be operated
by emergency stop signals set externally.
Electro-
magnetic
brakes
Servomotor
24VDC
RA1
EMG
Shut off with servo ON signal OFF,
alarm, electromagnetic brake signal.
Shut off with the
emergency stop
signal(EMG).
If an error occurs, remove the cause, secure the safety and then resume operation after alarm release.
The unit may suddenly restart after a power failure is restored, so do not go near the machine. (Design
the machine so that personal safety can be ensured even if the machine restarts suddenly.)
Confirm and adjust the program and each parameter before operation. Unpredictable movements may
occur depending on the machine.
Extreme adjustments and changes may lead to unstable operation, so never make them.
Do not apply a voltage other than that specified in the instruction manual on any terminal.
Doing so may lead to destruction or damage.
Do not mistake the terminal connections, as this may lead to destruction or damage.
Do not mistake the polarity ( + / - ), as this may lead to destruction or damage.
Do not touch the servo amplifier's heat radiating fins, regenerative resistor and servomotor, etc., while
the power is ON and for a short time after the power is turned OFF. In this timing, these parts become
very hot and may lead to burns.
Always turn the power OFF before touching the servomotor shaft or coupled machines, as these parts
may lead to injuries.
Do not go near the machine during test operations or during operations such as teaching. Doing so
may lead to injuries.
Do not bunch the control wires or communication cables with the main circuit or power wires, or lay
them closely. They should be installed 100 mm (3.94 inch) or more from each other.
Trying to bunch or install could result in noise that would cause operation failure.
- MOTION CONTROLLERS 1
- SAFETY PRECAUTIONS 2
- (1) System structure 4
- CAUTION 10
- 1. OVERVIEW 18
- (Note-2) : SSCNET: S 19
- 2. SYSTEM CONFIGURATION 20
- SSCNET cable 21
- (a) MR-H BN 39
- (c) FR-V5 0 41
- (4) Software packages 41
- (a) PLC software package 42
- 2.3 General Specifications 43
- (2) Q173CPU/Q172CPU 46
- Q172CPU(N) 48
- (a) Module specifications 49
- 2.4.2 Power supply module 55
- 100-120VAC 58
- (When using the Q173CPUN-T.) 61
- (4) I/O allocations 64
- (1) Q172LX name of parts 65
- (b) Input 66
- (a) Servo external signals 67
- • Tracking enable signal 73
- Q173CPU(N)/ 74
- Cable length 10m (32.81ft.) 76
- (b) Q172EX-S2/Q172EX-S3 77
- (a) Specifications 78
- Battery Specifications 78
- (b) Battery replacement 78
- Q173PX-S1 80
- (Note-1)(Note-2) 81
- (Duty ratio: 50% 25%) 86
- 20 s or more 86
- A4 A3 A2 87
- B4 B3 B2 87
- CN1A CN1B 101
- 2 SYSTEM CONFIGURATION 102
- (h) FR-V5NSCBL 107
- (a) MR-H-BN configuration 108
- (b) MR-J2 -B configuration 108
- 1) Example of Q173CPU(N) 110
- 2) Example of Q172CPU(N) 112
- 2.4.10 External battery 115
- 3. DESIGN 120
- 3 DESIGN 123
- 3.2 External Circuit Design 123
- MR-J2-03B5 124
- Electro 124
- (For A31TU-DN ) 125
- (For A31TU-D3 ) 127
- MC1 N0 M10 129
- (2) Grounding 131
- Forced stop 132
- Internal 132
- Wpw= (I 136
- 3.4 Design Checklist 139
- 4 INSTALLATION AND WIRING 141
- (1) Fitting dimensions 142
- Vertical Flat 143
- Motion CPU 146
- PC connector 147
- Battery cable 148
- CPU/BAT connecto 148
- Battery unit 148
- (Q170BAT) 148
- TU connector 149
- (3) Grounding 156
- [Servo data setting 162
- Power supply module 171
- PLC CPU module 171
- Motion CPU module 171
- I/O module 172
- 6.3 Periodic Inspection 173
- 6.4 External Battery 174
- (Note-1) 175
- (Note-3) 175
- (Note-2) 175
- MITSUBISHI 176
- LITHIUM BATTERY 176
- Lithium battery 178
- Memory card socket 178
- Is the power 182
- 132VAC or 170 to 264VAC? 182
- "RUN" LED 184
- For the case of 1) 184
- For the case of 2) 184
- When started the latch clear 186
- Are the output 188
- USB driver installed 190
- Win 98/2000/XP? 190
- DC input 192
- (plus common) 192
- Input module 192
- Resistor 192
- Output module 194
- APPENDICES 196
- PPENDICES 198
- (a) Q172J2BCBL M(-B) 198
- 1) Model explanation 198
- 2) Connection diagram 198
- (b) Q172HBCBL M(-B) 199
- Q173DVCBL M 200
- (d) Q173J2B CBL M 201
- (e) Q173HB CBL M 202
- :Twisted pair cable 203
- (h) MR-HBUS M 205
- (2) MR-JHSCBL M-L/H 207
- (a) Model explanation 207
- (b) Connection diagram 207
- (3) Q170ENCCBL M 208
- (Note) 209
- Q170TUD3CBL3M 211
- Q170TUDNCBL3M 212
- 27.4(1.08) 215
- 98(3.86) 215
- 114.3(4.50) 215
- 46(1.81) 215
- 79.5(3.13) 215
- (3) Q172CPUN-T Module 216
- (4) Q173CPUN-T Module 216
- (5) Q172CPU Module 217
- (6) Q173CPU Module 217
- (1) Q173PX 220
- (2) Q173PX-S1 220
- (2) Q64P 221
- (1) Dividing unit (Q173DV) 222
- (2) Battery unit (Q170BAT) 222
- APPENDIX 2.7 Connector 223
- (6) A31TUD3TM 227
- Effective dimension 229
- Keyway Dimensional Diagram 229
- WARRANTY 233
Related products and manuals for Power adapters & inverters Mitsubishi Electric Q172CPU
(34 pages)© 2020, manymanuals.com. All rights reserved. | 4.910 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals